THIS IS MINI
Portable OLED T12 solder iron station, doesn't include
power supply, if you need
to buy power adapter 24V3A, please contact us. You need
to buy a DC 24V 3A-5A power supply additional. Please
use a 3-5A power supply to drive this soldering station.
If you
want change the default Tip , please leave us a message.
Iron tip do not
work continuously high temperature, high temperature work is easy to damage the
tip!
Ordinary solder
melting point is 183 degrees, normal solder melting point is 227 degrees,
usually the welding temperature is 300-380degC, 380 degrees is the temperature
of the dividing line, higher than 380 degrees, iron head oxidation and loss is
extremely fast, seriously affect the heating core life The Higher than 380
degrees temperature display will be beating, the higher the temperature, the
greater the beating! Recommended in the 300-380 degrees for welding work, most
of the work can be carried out, the temperature beating is normal, does not
affect the use!
If can use low
temperature, then do not high temperature: T12 is constant temperature control,
the general recommended working temperature control between 300 ℃ ~ 380 ℃,
higher than 380 ℃ damage the coating of solder tip and cut down the PTC life!
We do not
recommend the use DC power supply adjustable, because regulated adjustable DC
power supplies cannot meet the requirements of instantaneous power. T12 has
special requirements for power supplies. Instantaneous power needs to reach 72W
or higher. Some brands of regulated power supplies cannot meet this
requirement. As a result, the 942 soldering station cannot be powered.
Dimensions:
38mm*41mm*88mm
Temperature
Stability: plus or minus 10C
Input Voltage:
DC24V
Output Power: MAX
75W
Output
Temperature: 200C-480C
Packaged weight:
250g
Power interface
size: DC 5.5*2.1mm
Regarding the
problem that the temperature displayed on the soldering station is not accurate
with the actual temperature:
Please use the
soldering iron tip temperature tester (please do not use a multimeter) to test
the temperature. When the soldering station is working at low temperature (less
than 280 degrees), the temperature displayed on the soldering station and the
actual temperature of the soldering iron tip are only for reference , which is
not accurate because They are affected by the surrounding environment. The
surrounding environment will carry away heat, causing the soldering iron tip to
lose some heat. If using a HB tip thermometer, pls make sure the soldering iron
tip is suspended at the center of the temperature sensing line. If you are very
strict with temperature, please do not buy this soldering station.
The problem that
tin wire cannot be melted at 227 degrees.
The melting point
is the melting point of the substance itself. When the temperature of the
substance reaches the melting point of the substance, it is possible that the
substance cannot be melted. For example, the melting point and freezing point
of ice are both 0 degrees Celsius, and water does not necessarily freeze at 0
degrees Celsius. Since the temperature of the substance is affected by the
surrounding environment, the actual melting point of the tin wire is higher
than the melting point indicated by the tin wire. If the wire is placed in a
thermostat tin furnace at 226 degrees Celsius, it is possible to melt in a
sealed tin furnace. If it is wrapped around the soldering iron tip, it is
impossible to melt. Because there is a gap between the tin wires, and the
soldering station has a temperature difference, the soldering iron will lose
some heat when it heats up, and the surrounding air will also absorb heat. The
melting point of normal wire is 227 degrees Celsius, and the room temperature
is low in winter. Under the premise of calibrating the temperature of the
soldering station, at least 50 degrees Celsius should be increased to offset
the heat absorbed by the air, so that the heat of the wire itself can be
increased to 228 degrees Celsius.
About the wake of
the handle
Please carefully
understand the working principle of the vibration switch in the handle. The
ball trigger switch built in the handle, the mounting direction of the ball
switch and the rolling direction of the ball inside the ball switch need to
vibrate the handle when the direction of the handle is consistent. For example,
when the handle is vertical Please move the handle up and down. When swinging
the handle up and down, please make sure that the ball inside the handle can
trigger the SW wake-up mode, and the force needs to be slightly larger. When
the handle is placed horizontally, please swing the handle left and right.
Please swing the handle to an angle greater than 30 degrees, so that the ball
inside the handle can trigger the SW wake-up mode.
About the
soldering station showing of ERROR
If the ERROR is displayed, the handle or the tip is not installed properly. Please use a pair of pliers to push the tip into the innermost part of the handle. Then try rotating the tip to ensure that the tab of the tip is in good connect with the inner tab of the handle. If ERROR is still displayed and the light is always on when the tip or handle is installed, please contact us to get a solution. We encourage buyers to communicate with us to solve any problems.