Technical Specification:
Plug type: high beam + low beam
LED quantity (each lamp): 4-sides * LED CSP chips
Luminous flux: 12000LM / set (6000LM / bulb)
Operating voltage: DC 12V (suitable for 12V vehicles)
Color temperature: 6000K white
Water and dust seal according to protection class IP67, service life over 50,000 hours, fanless
Beam angle: 360 degrees
Material: Aviation 6063 aluminum profile
Operating temperature: -40-80 degrees Celsius
Plug type: high beam + low beam
LED quantity (each lamp): 4-sides * LED CSP chips
Luminous flux: 12000LM / set (6000LM / bulb)
Operating voltage: DC 12V (suitable for 12V vehicles)
Color temperature: 6000K white
Water and dust seal according to protection class IP67, service life over 50,000 hours, fanless
Beam angle: 360 degrees
Material: Aviation 6063 aluminum profile
Operating temperature: -40-80 degrees Celsius
Advantage:
* Latest chip light source, 4 luminous areas with no blind zone
* The design of the technical beam pattern casts more light evenly on the road at a suitable angle, without foggy light
* White light better reflects road color / signs to indicate a clearer road situation during night driving
* A cut-off angle of 270 degrees with a dividing line does not dazzle oncoming traffic
* Built-in constant current CPU, instant full brightness without starting relay
* Latest chip light source, 4 luminous areas with no blind zone
* The design of the technical beam pattern casts more light evenly on the road at a suitable angle, without foggy light
* White light better reflects road color / signs to indicate a clearer road situation during night driving
* A cut-off angle of 270 degrees with a dividing line does not dazzle oncoming traffic
* Built-in constant current CPU, instant full brightness without starting relay
Installation Caution:
1. For safety reasons, make sure the vehicle has had time to cool down properly before starting the installation.
2. Park the vehicle or make sure it is in gear.
3. Make sure the ignition is off and the keys are removed.
4. Avoid burns, especially when switching the vehicle lights on and off.
5. Be careful not to crush or cut the lightbulbs. Also, be careful not to touch the lightbulbs with your fingers as this can cause staining.
6. Completely inspect the connection of the contact points, connectors and wires, as incorrect connections can lead to lighting problems.
7. Make sure that the end of the light bulb does not come into contact with the inner light shield of the headlight when adjusting the light bulb.
8.Please install the car headlight dust cover to ensure the normal operation of the lamp
1. For safety reasons, make sure the vehicle has had time to cool down properly before starting the installation.
2. Park the vehicle or make sure it is in gear.
3. Make sure the ignition is off and the keys are removed.
4. Avoid burns, especially when switching the vehicle lights on and off.
5. Be careful not to crush or cut the lightbulbs. Also, be careful not to touch the lightbulbs with your fingers as this can cause staining.
6. Completely inspect the connection of the contact points, connectors and wires, as incorrect connections can lead to lighting problems.
7. Make sure that the end of the light bulb does not come into contact with the inner light shield of the headlight when adjusting the light bulb.
8.Please install the car headlight dust cover to ensure the normal operation of the lamp
Delivery content:
4 PCS LED lamps
4 PCS LED lamps
Attention:
LED lamp is a device with low power consumption. The following problems may arise when trying to use LED bulb in some European vehicles: Hyper Flashing, No Flashing, or Error Code. These are NOT issues with LED lamps and are NOT covered by the warranty. You can just add a set of load resistor (NOT included) to avoid these problems. Can be solved with a decoder (decoder must be purchased separately).
LED lamp is a device with low power consumption. The following problems may arise when trying to use LED bulb in some European vehicles: Hyper Flashing, No Flashing, or Error Code. These are NOT issues with LED lamps and are NOT covered by the warranty. You can just add a set of load resistor (NOT included) to avoid these problems. Can be solved with a decoder (decoder must be purchased separately).
If the product is unsuitable or there is any quality problem, please contact our customer service directly to resolve the problem. We will give you a satisfactory solution.