There is a QR cooe on the panel of our cntolle, you just need to scan it to get the operating istuctins.

Please contact us for the operating instructions ol the display.

Our display is only compatale with the communication prtocodl of our contrlle or OMD. .

I you canot confim the type of communication prolocol, please do not buy the dsplay separalely.

To purchase the contole or disply separtely, please contatct us to confim and edjust the shpping cost apropritel.

Very important Motice

This crtlel can only work without display or with our displey, please neer use it wth your own display (ecuse progam is imlett

Wiy 3-mode Crtlle?

Support Hall Sensor Mode (Sine Wave Mode)

Support Non-Hall Mode (Ir your motor hall sensor bumed or not match, cnrtrllerl will stl work in square wave mode)

el-erring Function: Even wrong 3-phase combination between motor and corole, doesn't matte, above sel-eaming process can correct it!

Adwantage:

1. Sine Wave Cortoller which support J-mode (hall sensor mode, non-hall mode, sl-erming) and smart match with each motor through ellr-

lerming, works with high emienc,. less noise, and lower energy corsumpion, which makes your electic velides or eetric motorcycles more

comfortable and exsier to corntrol, give you best pedal experience

2. Universal Input Woltage Range: 36V/4BV/52V

3. Work with or without display

4. Parameter slting wia Gisplay

5. AI protection make it long R'e and sale: over/under vllage, over curent, over load, over heating., ant-runaway, locked-motor protection

6. Multi functions: Work with hall sernsor mode or non-hell mode, smart match with dierent moto, 5-speed level fo throtte and PAS, Speed limt,

Reverse, Cruise, Push Asistant, Ant-thiet, Regenerdive Braking, Eletric Braking and etc.

7. Best heat sink ng with Auminium Case

8. Black andied Auminium Cortroler Case against scratch

Technical Data:

General Speilncation:

1. Rated Power: 36V 792W/ 4BV 1056W/ 52V 1144W1

2. Peak Power: 36V 1620W/ 48V 2160W/ 52V 2340W

3. Brake: Low Vltage Brake

4 Narm: Low Vltage Narm

5. Rotor Position Detecting Method: Hall sensor

6. Siae: 212xB6.5x4B. 5mm

7. Net Weight: 610g

8. Watepror Grade: IP65

FAQ:

1. How shall I malch my motor for frst time use? (very Important)

(Please check Crtrlle Connection Diagram and Manuel, Page 1)

1). Lit your moltor wheed o( ground (very important)

2). Connect Sl-earring plug 6-8 seonds

3). You will see motior whee rotate slowly

4). Please check wthethler rotelion direction is crret

(a). II coret dnection, then keep 6-8 seconds, then disconnet

(B). Ir reverse drection, then disconect and plug again ill get correct rotation diretion, then keep 6-B seconds, then disconnect

5). Motor and Controler Pairing finished!

2. CanI use this crtroler without display?

Yes, you can use this croller without dsplay, just need t如connect jumper cornetor (Please check Cortrole Cornetion Diagram and Manual,

Page 4, point No.3)

3. How can I limit spee?

In some counties, below 25km/h speed s requred on road, you can switch on/0T speed limit function by coneting a simple switch to cnrtroler

speed Imit plug, or you can even conmect jumper connector to alwaps lmit speed (Please check Cornroller Connection Diagram and Manuel, Page 9-

10, point No.12)