2023 New Handheld Tiny Spectrum Analyzer TinySA ULTRA 4" Display 100kHz to 5.3GHz with 32GB Card Version V0.4.5.1
Specification：
| Parameter | Specification |
| Display size | 4” TFT LCD (480×320) |
| Max low input frequency | 800MHz, 6GHz in Ultra mode |
| Resolution filters in 1,3,10 steps | from 200Hz to 850kHz |
| Max output frequency | Sinus up to 800MHz, Square wave up to 4.4GHz |
| output level | -104dBm to -16dBm |
| Ultra mode | Level calibrated up to 5.3GHz |
| Internal LNA gain | 20dB up to 4GHz |
| Displayed points per scan | max 450 |
| 0-350MHz scan time | 165ms |
| Shortest zero span time | 17ms |
| DANL at 100MHz | -153dBm/Hz (LNA Off) / -169dBm/Hz (LNA On) |
| DANL degrading in ultra mode | 10dB above 2.5GHz, 25dB above 5.3GHz |
| Phase noise at 10kHz offset | -92dBc/Hz |
| Phase noise at 100kHz offset | -110dBc/Hz |
| Input 1dB compression level | +0.5dBm (LNA Off) / -26.5dBm (LNA On) |
| IIP3 without LNA | +18dBm (at least 2MHz apart) / 0dBm (500Hz apart) |
| IIP3 with LNA | -8dBm (at least 2MHz apart) |
| Frequency stability | <1ppm ( -10℃ ~ +55℃) |
| SD card slot | micro SD card |
| Audio out | 3.5mm headphone plug |
| FW update mode activation | Push jog button before switch on |
| Maximum current consumption | 330mA |
| Maximum charging current | 1300mA |
| Battery | Li-polymer 3.7V 3000mAh |
| RF connectors | SMA female |
| Communication Interface | USB-CDC(Type-C)，UART-TTL(2.54mm Connector) |
| Appearance Size | 117x72x23mm (Excluding protruding parts) |
TinySA model comparison table：
| tinySA | tinySA Ultra | |
| Display size | 2.8 inch | 4 inch |
| Max low input frequency | 350MHz | 800MHz, 6GHz in Ultra mode |
| High input range | 240MHz - 960MHz | Not available |
| Resolution filters in 1,3,10 steps | from 3kHz to 600kHz | from 200Hz to 850kHz |
| Max low output frequency | 350MHz | Sine wave up to 800MHz, Square wave up to 4.4GHz |
| Low output level | -76dBm to -7dBm | -104dBm to -16dBm |
| High output frequency range | 240MHz - 960MHz | Not available |
| High output level | -32dBm to 16dBm | Not available |
| Ultra mode | Not available | Level calibrated up to 6GHz |
| Internal LNA gain | Not available | 20dB up to 4GHz |
| Internal step attenuator | Normal: 0-31dB, High: NA | 0-31dN |
| Displayed points per scan | max 290 | max 450 |
| 0-350MHz scan time | 405ms | 165ms |
| Shortest zero span time | 1.8ms | 17ms |
| DANL low input at 100MHz | -146dBm/Hz | -153dBm/Hz (LNA Off) / -169dBm/Hz (LNA On) |
| DANL high input at 880MHz | -163dBm/Hz | Not available |
| DANL degrading in ultra mode | 10dB above 2.5GHz, 25dB above 5.3GHz | |
| Phase noise at 10kHz offset | -83dBc/Hz | -92dBc/Hz |
| Phase noise at 100kHz offset | -98dBc/Hz | -108dBc/Hz |
| Low input 1dB compression level | -0.5dBm | +0.5dBm (LNA Off) / -26.5dBm (LNA On) |
| IIP3 without LNA | +24dBm | +18dBm (at least 2MHz apart) / 0dBm (500Hz apart) |
| IIP3 with LNA | Not available | -8dBm (at least 2MHz apart) |
| SD card slot | Not available | micro SD card |
| Audio out | Not available | 3.5mm headphone plug |
| FW update mode activation | Via DFU menu | Push jog button before switch on |
| AM modulation depth | Fixed 30% | 10% and 100% |
| FM deviation | 4kHz or 75kHz | 1kHz to 300kHz |
| Modulation frequency | 50Hz to 5kHz | 50Hz to 5kHz(AM) or 1kHz(FM) |
Package includes:
Host (with 3000mAh battery, 4"display) x 1
USB Type-C data cable x1
30cm ALSR100 SMA cables x2
SMA-SMA barrel connector x1
Antenna with SMA connector x1
Lanyard and touch plectrum x1
32GB MicroSD card(plugged in the host) x1
Am 18.08.2023 hat der Verkäufer die folgenden Angaben hinzugefügt: