4x Oxygen O2 Sensor For BMW 128i 2008-2013 328i 2007-2013 X3 X5 2007-2010 3.0L
Specification:
Condition:100% Brand New And High Quality
(5-wire oxygen sensor): Upstream Front, Cylinder 1-3, before catalytic converter 1X
(5-wire oxygen sensor): Upstream Rear, Cylinders 4-6, before catalytic converter 1X
(4-wire oxygen sensor): Downstream Front, Cylinders 1-3, after catalytic converter 1X
(4-wire oxygen sensor): Downstream Rear, Cylinders 4-6, after catalytic converter 1X
Vehicle Fitment:
for BMW
125i 3.0L 2012-2013
128i 3.0L 2008-2013 E82; E88
130i 3.0L 2006-2010
323i 2.5L 2010-2011
325i 2.5L 2006-2011
325i 3.0L 2006
330i 3.0L 2006
330xi 3.0L 2006
528i 3.0L 2008-2010
for 328i
2007-2011 E90; E91; E92; E93
2012-2012 E91; E92; E93
2013-2013 E92; E93
328i xDrive
2009-2011 E90; E91; E92
2012-2012 E91; E92
2013-2013 E92
328xi
2007-2008 E90; E91; E92
X3
2007-2008 E83; 3.0si
2009-2010 E83; xDrive30i
X5
2007-2008 3.0si
2009-2010 3.0 xDrive30i
Package Include:
4Pcs Oxygen Sensor
Note:
Please check the picture and the part number carefully to make sure that you bought the right part for your car.The only way to be 100% sure that the part will fit your vehicle is to check your part,You can also email us before purchasing, we will check for you and reply soon within 24 hours.
Q&A
Q:Why does the oxygen sensor have false alarm, after installation ?
A:The clearing of the errors can be obtained on most systems when the vehicle battery is disconnected for at least 60 seconds. The assignment of the new sensor parameters is done automatically when the errors are cleared, but in some systems a short adapting tour is required. In this case the vehicle has to be driven on the road for some 10-15 minutes, in order to have the ECU adapt itself to the new sensor.
Q:How do I know the O2 sensor is good or not ?
A:The only way to know if the O2 sensor is functioning normally is to check its responsiveness to changes in the air/fuel mixture, by Voltage Measurement or Waveform Simulation.
Q:How should I install oxygen sensor ?
A:The following is the installation instructions: Use the correct part number as listed in the application catalogue ,Do not use sensor if i has been dropped ,Remove protection cap just prior to installation;
Firstly install sensor body ensuring lead wire is not twisted or bent , Do not use impact wrench or socket type wrench to install sensor ,M18 sensors - install finger tight then 1/2-3/4 turn with a wrench (35-45Nm) ;
Then connect and route lead wire as originally installed , Do not allow lead wire to touch exhaust manifold or any other hot component ,Do not apply any substances (especially oil or grease) to connector sensor ,Do not use leaded fuels,silicone or metal based additives.
Q:When should replace the oxygen sensor?
A:Oxygen Sensor Failure Symptoms:
Reduced fuel mileage
Failed emissions testing
A check engine light
Poor drive-ability
#6 – Your engine surges, hesitates, skips and bucks.
Condition:100% Brand New And High Quality
(5-wire oxygen sensor): Upstream Front, Cylinder 1-3, before catalytic converter 1X
(5-wire oxygen sensor): Upstream Rear, Cylinders 4-6, before catalytic converter 1X
(4-wire oxygen sensor): Downstream Front, Cylinders 1-3, after catalytic converter 1X
(4-wire oxygen sensor): Downstream Rear, Cylinders 4-6, after catalytic converter 1X
Vehicle Fitment:
for BMW
125i 3.0L 2012-2013
128i 3.0L 2008-2013 E82; E88
130i 3.0L 2006-2010
323i 2.5L 2010-2011
325i 2.5L 2006-2011
325i 3.0L 2006
330i 3.0L 2006
330xi 3.0L 2006
528i 3.0L 2008-2010
for 328i
2007-2011 E90; E91; E92; E93
2012-2012 E91; E92; E93
2013-2013 E92; E93
328i xDrive
2009-2011 E90; E91; E92
2012-2012 E91; E92
2013-2013 E92
328xi
2007-2008 E90; E91; E92
X3
2007-2008 E83; 3.0si
2009-2010 E83; xDrive30i
X5
2007-2008 3.0si
2009-2010 3.0 xDrive30i
Package Include:
4Pcs Oxygen Sensor
Note:
Please check the picture and the part number carefully to make sure that you bought the right part for your car.The only way to be 100% sure that the part will fit your vehicle is to check your part,You can also email us before purchasing, we will check for you and reply soon within 24 hours.
Q&A
Q:Why does the oxygen sensor have false alarm, after installation ?
A:The clearing of the errors can be obtained on most systems when the vehicle battery is disconnected for at least 60 seconds. The assignment of the new sensor parameters is done automatically when the errors are cleared, but in some systems a short adapting tour is required. In this case the vehicle has to be driven on the road for some 10-15 minutes, in order to have the ECU adapt itself to the new sensor.
Q:How do I know the O2 sensor is good or not ?
A:The only way to know if the O2 sensor is functioning normally is to check its responsiveness to changes in the air/fuel mixture, by Voltage Measurement or Waveform Simulation.
Q:How should I install oxygen sensor ?
A:The following is the installation instructions: Use the correct part number as listed in the application catalogue ,Do not use sensor if i has been dropped ,Remove protection cap just prior to installation;
Firstly install sensor body ensuring lead wire is not twisted or bent , Do not use impact wrench or socket type wrench to install sensor ,M18 sensors - install finger tight then 1/2-3/4 turn with a wrench (35-45Nm) ;
Then connect and route lead wire as originally installed , Do not allow lead wire to touch exhaust manifold or any other hot component ,Do not apply any substances (especially oil or grease) to connector sensor ,Do not use leaded fuels,silicone or metal based additives.
Q:When should replace the oxygen sensor?
A:Oxygen Sensor Failure Symptoms:
Reduced fuel mileage
Failed emissions testing
A check engine light
Poor drive-ability
Symptoms of a Bad Oxygen Sensor
#1 –
Check engine light on 
,
Code checker identifying O2 sensor failure .
,
Code checker identifying O2 sensor failure .
You can diagnose the problem yourself if you have access to the right tools OBD2 diagnostic tool. O2 Sensor Codes include P0030, P0031, P0036, P0037, P0130, P0131, P0132, P0133, P0134, and P0135.
#2 –
A rotten egg odor emitting from the exhaust.
#3 –
A reduction in fuel economy.
#4 –
Your catalytic converter fails unexpectedly.
#5 – Exhaust emissions reach undesirable levels.
