ANCEL PB500 Description: Ancel PB500 has 7 test modes: DC Voltage, AC Voltage, Frequency, Duty Cycle, Fuel Injection Circuit Detection, Resistance, and Diode. Especially, in AC Voltage, Frequency, Duty Cycle and Fuel Inject Modes, user can long press the mode button to switch between Waveform Display Mode and Digital Display Mode. After the power is turned on, short press the mode button to enter the menu, select the test mode by pressing the up and down keys, and then press the mode button to enter the desired test mode. ![]() ![]() |
ANCEL PB500 Features
![]() ![]() |
More Useful Features ●4 modes to diagnose the electrical system: DC voltage, AC voltage, resistance, diode. ●Voltage & Polarity Test: According to the LED light and sound after the probe tip touches the circuit, it can accurately judge the positive, negative, and open circuits. ●Continuity Test: While the tool is in Resistance mode, using the probe tip with chassis ground or the auxiliary ground lead, continuity can be tested on wires and components attached or disconnected from the vehicle’s electrical system. ●Signal Circuit Test: When the vehicle has a fault code, in order to quickly determine whether the fault is caused by a certain sensor circuit, you can use this tool to quickly draw a conclusion. ●Find Short Circuit: A short can manifest itself as a blown fuse or a tripped electrical protection device. Use the probe tip to activate and energize each fuse contact. The contacts that trip the circuit breaker are shorted. ●Find Bad Ground: Probe for suspected ground wires or touch probe tips. If the breaker has tripped, the circuit is most likely grounded. ●Activate Component in your hand/ in the vehicle/ W/Ground ●Test Trailer Lights and Connections: Check function and orientation of connectors and trailer lights ●Red/Green Polarity Indicator: The red/green polarity LED illuminates when the probe tip voltage matches and is within ±0.8 volts of the battery voltage. It is additional information that may be of value to a technician. ![]() ![]() ![]() |
7 Working Modes: DC Voltage, AC Voltage, Frequency, Duty Cycle, Fuel Injection Circuit Detection, Resistance, and Diode DC Voltage: While the tool in this mode, contact the probe tip to a circuit, then the LCD display will read the DC voltage with a resolution of 0.1 volt. |
20ft Extension Cable: Autel PowerScan 100 itself has an extra-long 20ft cable, considering the volume of 12V-24v vehicles such as ships and trucks, we have additionally equipped with extra 20FT extension cable for emergencies. With the 20FT extension cable, you can freely test the condition of any vehicle circuit without moving the device because the cable is not long enough. ![]() |
Two Power Supply Methods: Vehicle battery power supply & Ciga-rette li-ghter power supply ![]() |
Quick Self-Test: Before you test a circuit or component, be sure your tool is in good order by doing a quick self-test. With the tool connected, perform a quick self-test. The power switch is a momentary rocker switch located on the tool's body. Flanking the switch are positive and negative markings. Press the Power Switch forward to activate the tip with a positive voltage. The Red LED should light and the LCD display will read the battery voltage. If the tone feature is turned on, a high pitched tone will sound. Let go of the power switch and the LED will turn off and the high tone will cease. Press the Power Switch rearward to activate the tip with a negative voltage. The Green LED should light and the LCD display will read the „0.0V‟ (ground). If the tone feature is turned on, a low pitched tone will sound. Let go of the power switch and the LED will turn off and the low tone will cease. Your tool is working correctly and is now ready for use. ![]() |
Package List: 1.Vehicle Super Probe x1 2.Probe Tip x1 3.Crochet Hook x1 4.Crochet Hook Extension Cable x1 5.Battery Clamp Cable x1 6.Rugged Blow Molded Case x1 7.User's Manual x1 ![]() ![]() ![]() |