Description
Our replacement window regulator is precision-engineered and extensively tested to match the exact fit, function and performance of the stock window regulator on specific vehicle years, makes and models. This replacement window regulator is precision-engineered and extensively tested to match the exact fit, function and performance of the stock window regulator on specific vehicle years, makes and models.
Your Checklist
Use the compatibility chart to identify your vehicle.
Visually compare the part you are replacing with our pictures.
Match reference numbers from the Item specifics section above.
Find the year,make, model, engine and trim in vehicle application to ensure.
Part Number
741-637 10315144, 10334397, 10434882, 19245391
Fitting for the following vehicles
1997-2005 Buick Regal
1997-2005 Buick Century
1998-2002 Oldsmobile Intrigue Front Left
Package
1x Window regulator with Motor in a box
Install the window regulator as follows:
Tools required for removal and installation of window regulator and motor assembly:
• Silicone spray lubricant
• Trim panel removal tool
• Pick
• Saddle cup assembly, tape, or wedge to hold window in place
• Flat-blade screwdriver or plastic pry tool
• 10mm socket or driver
• Phillips screwdriver
• Grease pencil or marker
• T-30 Torx bit
Removal Instructions
STEP 1: Using a pick or small flat-blade screwdriver, remove the interior door pull retaining screw cover plate.
STEP 2: Using a 10mm socket and ratchet assembly, remove the two (2) interior door pull retaining screws.
STEP 3: Using a trim panel removal tool, remove the interior door trim panel assembly. NOTE: Placing the trim panel removal tool between the interior door trim panel and the door, pry the tool toward you to release the interior door trim panel retaining clips.
STEP 4: Disconnect the power window switch assembly.
STEP 4a: Disconnect the power door switch assembly.
STEP 5: Disconnect the door harness connector.
STEP 6: Using a 7mm socket and ratchet assembly, remove the four (4) door speaker mounting screws.
STEP 7: Disconnect the door speaker.
STEP 8: Remove the interior door trim panel.
STEP 9: Remove the water vapor barrier.
STEP 10: Using a T-30 Torx bit and ratchet assembly, remove the Torx bit retaining the interior door trim panel support bracket.
STEP 11: Temporarily connect the power switch assembly and lower the door glass, exposing the screws attaching the window regulator to the door glass.
STEP 12: Using a 10 mm socket and ratchet assembly, remove the four (4) interior door trim panel support bracket retaining screws. NOTE: The four (4) interior door trim panel support bracket retaining screws also hold the window regulator in place.
STEP 13: Disconnect the power switch assembly.
STEP 13a: Using a 10mm socket and ratchet assembly, remove the two (2) screws attaching the window regulator to the door glass.
STEP 14: Once the door glass has been separated from the window regulator, manually slide the door glass into the closed position and hold in place with either a saddle cup assembly, painter’s tape, or a wedge.
STEP 15: Disconnect the window lift motor connector.
STEP 16: Using a 10 mm socket and ratchet assembly, remove the three (3) window lift motor retaining screws.
STEP 17: Remove the window regulator through the main access hole in the door.
Installation Instructions
STEP 1: Install the window regulator through the main access hole.
STEP 1a: Using a T-30 Torx bit and ratchet assembly, attach the interior door trim panel support bracket.
STEP 2: Using a 10 mm socket and ratchet assembly, attach the four (4) window regulator/interior door trim panel support bracket retaining screws.
STEP 3: Using a 10mm socket and ratchet assembly, attach the three (3) window lift motor attaching screws.
STEP 4: Connect the window lift motor connector.
STEP 5: Temporarily connect the power switch assembly to raise or lower the window regulator, aligning the points mounting the door glass to the window regulator.
STEP 6: Manually slide the door glass into position, aligning the points attaching the door glass to the window regulator. STEP 6a: Using a 10mm socket and ratchet assembly, attach the door glass to the window regulator.
STEP 7: Attach the water vapor barrier.
STEP 8: Connect the door speaker.
STEP 8a: Using a 7mm socket and ratchet assembly, attach the four (4) door speaker attaching screws.
STEP 9: Connect the power switch assembly connector.
STEP 9a: Connect the power door lock switch. STEP 9b: Connect the door harness connector.
STEP 10: Install the interior door trim panel assembly. NOTE: Be sure to align all of the interior door trim panel retainers. Failure to do so may result in damage to the interior door trim panel or the interior door trim panel retaining clips.
STEP 11: Using a 10 mm socket and ratchet assembly, attach the two (2) interior door pull retaining screws.
STEP 12: Install the interior door pull retaining screw cover plate.
STEP 13: Verify that the interior door trim panel is secure and that the window regulator is operating properly.
Warranty:
This product is covered by our 1-year warranty.
If a failure occurs due to a manufacturing defect during the expected use, we will replace the part free of charge