Features:
*1. Built-in Calibration Signal Generator, when not doing spectrum analyzer, it can be used as signal generator with two frequency outputs,M F/HF/VHF sinus output for 0.1MHZ-350MHz and UHF square wave output for 240MHz-960MHz. It is used for automatic self test and low input calibration.
*2. This Spectrum Analyzer with two inputs ,high quality M F / HF / VHF Input for 0.1MHZ-350MHZ and lesser quality UHF Input for 240MHZ- 960MHz.
*3. PC Control.This spectrum analyzer can be connected to PC through USB, and realizes the serial over USB (CDC) protocol, which can call a large number of commands. After connecting the PC, the driver will be downloaded automatically.
*4. ESD Protection Function. The latest version 3.1, new ESD protection function, installed diodes,so that it has more sensitive response performance, efficient anti-static level, better quality, longer service life.
*5. Connected to a PC via USB it becomes a PC controlled spectrum analyzer.
*6. Rechargeable battery allowing a minimum of at least 2 hours portable use.
Specifications:
Material: ABS
Color: black
Battery: 1 * lithium battery, 650mAh (included)
Package size: 200 * 120 * 30mm / 7.9 * 4.7 * 1.2in
Package weight: 250g / 8.8ounce
Technical indicators:
User interface:
Display resolution 320*240 pixels
Screen diagonal 2.8"
16 bits per RGB pixels
Resistive touching control
Jog switch control
USB serial port control
Optional TTL USART port (SW not yet implemented) on the internal PCB
Linear power supply to refrain switching noise
The input/output specification of the is split over the 4 modes.
Low input mode spec:
Input frequency range from 100KHz to 350MHz.
Input impedance 50 ohm when input attenuation set to 10dB or more.
Selectable manual and automatic input attenuation between 0dB and 31dB in 1dB steps.
Absolute maximum input level without attenuation of +10dBm.
Absolute maximum input power with 30dB attenuation of +20dBm for short period.
Input intercept point of third order modulation products (IIP3) with 0dB attenuation of +15dBm.
1dB compression point at +2dBm with 0dB attenuation.
Power detector resolution of 0.5dB and linearity frequency of +/-1dB.
Absolute power level accuracy after power level calibration of +/-1dB.
Lowest discernible signal using a resolution bandwidth of 30KHz of -102dBm.
Frequency accuracy equal to the selected resolution bandwidth.
Phase noise of -90dB/Hz at 100KHz offset and -115dB/Hz at 1MHz offset.
Spur free dynamic range when using a 30KHz resolution bandwidth of 70dB.
Manually selectable resolution filters of 3, 10, 30, 100, 300, 600KHz. Automatic selection of 1 of the 57 resolution filters.
On screen resolution of 51, 101, 145 or 290 measurement points.
Scanning speed of over 1000 points/second using largest resolution filters.
Automatic optimization of actual scanning points to ensure coverage of the whole scan range regardless of the chosen resolution bandwidth.
Spur suppression option for assessing if certain signals are internally generated or actually present in the input signal.
High input mode spec:
Input frequency range from 240MHz to 960MHz.
Input impedance is frequency dependent and deviates from 50ohm.
As there is no input bandfilter, strong input signals outside the 240MHz to 960MHz range can cause distortion of the in band signals.
Absolute maximum input level without attenuation of +10dBm.
Input intercept point of third order modulation products (IIP3) of -5dBm.
1dB compression point at -6dBm with no attenuation.
Power detector resolution of 0.5dB and linearity frequency of +/-1dB.
Absolute power level accuracy after power level calibration of +/-1dB.
Lowest discernible signal using a resolution bandwidth of 30KHz of -115dBm.
Frequency accuracy equal to the selected resolution bandwidth.
Spur free dynamic range when using a 30KHz resolution bandwidth of 50dB.
Manually selectable resolution filters of 3, 10, 30, 100, 300, 600KHz. Automatic selection of 1 of the 57 resolution filters.
Optional 25dB to 40dB frequency dependent input attenuator. The power level error with this attenuator activated increases to +/-10dB.
On screen resolution of 51, 101, 145 or 290 measurement points.
Scanning speed of over 1000 points/second using largest resolution filters.
Automatic optimization of actual scanning points to ensure coverage of the whole scan range regardless of the chosen resolution bandwidth.
Low output mode spec:
Sinus output with harmonics below -40dB of fundamental.
Output frequency range from 100KHz to 350MHz.
Output level selectable in 1dB steps between -76dBm and -6dBm.
Optional AM, narrow FM and wide FM modulation or slow sweep over selectable frequency span.
Optional output level sweep over maximum the entire output level range.
High output mode spec:
Square wave output.
Output frequency range from 240MHz to 960MHz.
Output level selectable in variable increments between -38dBm and +13dBm.
Optional narrow FM and wide FM modulation or slow sweep over selectable frequency span.
Reference generator spec:
Optional square wave output with fundamental at -25dBm connected to high input/output.
Frequency can be set to 1MHz, 2MHz, 4MHz, 10MHz, 15MHz or 30MHz.
Battery spec:
Charging time max 1 hour on 500mA minimum USB port or USB recharger.
Operation on fully charged battery for at least 2 hours.
Package include
1 x Spectrum Analyzer
2 x SMA Cable and A Connector
1 x Antenna with An SMA Connector
1 x USB-C Cable
1 x Touching Screen Paddle
