Notice: this set of models is recommended only for expert modelers with previous experience removing supports from 3D-printed models.  Support removal is very difficult.  Novice modelers and those without previous 3D-printed modeling experience may struggle to remove supports without damaging the models.

If you have no experience with 3D-printed models, please do not buy this product.

For combined shipping with other Model Monkey products, add to cart.  Do not select "buy it now".

Scale: 1/400

Set includes 4 funnels and 4 triple-whistles.

Recommended for:

• Academy 1/400 scale RMS Titanic
• Doyusha 1/400 scale RMS Titanic
• Hasegawa 1/400 scale RMS Titanic
• JSC 1/400 scale RMS Titanic
• Modelist 1/400 scale RMS Titanic
• Revell 1/400 scale RMS Titanic
• Schreiber-Bogen 1/400 scale RMS Titanic Junior Model
• and more!

These accurately sized and highly detailed models represent the four funnels of Olympic class White Star liner RMS Titanic.  They are scaled from scans of Harland and Wolff builder's plans.

Features:

• Seamless smoke pipe uptakes.
• Accurate, extensive rivet detail, properly sized, numbered and located, with 15 vertical rows of rivets.
• Accurate height consistent with Harland and Wolff's "Titanic Rigging Plan":
  • Funnels 1 and 4 = 163 feet 8 inches above keel
  • Funnels 2 and 3 = 165 feet 2 inches above keel (18 inches taller than Funnels 1 and 4)
• Accurate aft slope ("rake") angle of 9.46 degrees from vertical (2 inches aft for every 12 inches of height), consistent with Harland and Wolff's "Titanic Rigging Plan".
• Accurate funnel "stay eyes", also called "shroud brackets", properly shaped and located.  The "stays" are a set of 12 cables, also called "shrouds", attached to each funnels' exterior.  The stays extend outward and downward from each funnel to the deck to stabilize and strengthen them.  The stays attach to "eyes" which are brackets bolted the funnel.  Plastic kits omit the eyes in favor of simple holes in the sides of the funnels.
• Accurately sized and configured exterior water and steam pipes:
  • large boiler steam escape pipes, 17" scale diameter forward pipe, 15" scale diameter aft pipe
  • whistle steam supply pipe with accurately bent base
  • integrated steam loops
  • integrated single-pipe P-shaped tank air vent/overflows
  • integrated double-pipe P-shaped tank air vent/overflows
• Accurately shaped triple whistles scaled from photos of a recovered set from the wreck.
• Accurate funnel cap interior with structural girders and braces.

The whistle service platform and ladder have been omitted in favor of photo-etch available from photo-etch vendors.

The funnels' external piping and steam whistles are very fine and fragile.

Titanic's Funnel Number 3 had a complex arrangement of exterior water pipes with one or both ends of most pipes extending aft to Titanic's tank room roof.  Pipe orientation and sizing matches drawings by noted Titanic researcher Bob Read.

• Click here for Mr. Read's drawings and for more information regarding Titanic funnels' exterior water and steam piping.
• Click here for more information about Titanic's funnels' exterior details.
• Click here for general information about Titanic and sisterships Olympic and Britannic.
• Click here for a Titanic color guide.

These scale model funnels are not 3D-printed copies of any plastic, resin, wood or paper card model kit’s parts. These funnels may not be the same size and shape of your plastic, resin, wood or paper card model kit’s parts. Some adjustment of your plastic or paper card kit’s parts or any aftermarket products such as photo-etch may be necessary for best fit.

Notice: this set of models is intended for very advanced modelers.  Each model includes supports that are similar to the sprues attached to injection-molded plastic kit parts.  Support removal, especially from each funnel's exterior piping, triple whistle and from each funnel cap's interior cross braces, is difficult.  Each funnel's exterior piping and triple whistle is fragile.  Therefore, a very sharp cutting instrument, care and patience are recommended when removing the suports and during handling.  Heating your cutting instrument may help.

Tips for removing interior supports:  There are several interior supports that are difficult to remove. Supports must be removed by the modeler.

1. From the top of Funnels 1-3, carefully locate and cut as many of the support contact points from the bottom of the 3 horizontal cross braces as possible.
2. Cut away and discard the printing raft from the bottom of each funnel. Leave the interior supports within the funnel cap.
3. From the bottom of all four funnels, carefully, gently and slowly twist the interior vertical supports to break them away from the bottom of the three horizontal cross braces. The contact points of the supports are very small and weak. With care, the vertical supports will break away without damaging the horizontal cross braces.

© Model Monkey LLC.  This 3D-printed product may not be copied or recast.