eBay

Feature:

1. Humanized design, the interface uses a terminal, a standard heat sink, and an integrated speed potentiometer on the board
2. Full chip technology, stable performance, with forward and reverse, brake function, motor speed controller adopts Hall brushless controller
3. Wide voltage 6‑60V high power 400W DC three‑phase brushless with Hall controller
4. Support PLC 0‑5V analog control, support PWM to 0‑5V control, can be used when power is on, saving time and effort
5. There are three relatively thick phase wires on the machine, and there are also three phase wire interfaces on the drive board, which are marked MA, MB, MC, etc.

Specification:

Item Type: Motor Controller
Material: PCB
Purpose: Motor Controller
Working Voltage: 6-60V
Maximum Current: Rated 16A Maximum 20A
Maximum Power: 400W
Overcurrent Protection: Yes

Package List:

1 x Motor Controller

1 x Terminal Line

Note:

1. This drive is a DC three‑phase brushless control board, which requires the motor to have a Hall to work normally

2. This drive is only suitable for DC brushless and Hall motors with an electrical angle of 120°

3. When the PWM is input from the 2 ports of the motherboard P G (the built‑in potentiometer on the board is adjusted to the minimum, and the short interface on the board is shorted at the same time, the wiring is shown in the figure above), the amplitude is 2.5‑5V, and the frequency is 50HZ‑20KHZ.

4. When the external analog 0‑5V input, input from the 2 terminal ports of the main board (the potentiometer on the board is adjusted to the minimum, the wiring is shown by the dotted line in the figure above)

5. When the external potentiometer is used to adjust the speed, connect it to the 3 terminal ports of the main board (the potentiometer on the board is adjusted to the minimum, and the wiring is indicated by the potentiometer on the picture)

6. The forward and reverse rotation and stop are grounded through a switch (0 potential). The low level is valid, and the external MCU can also give a low level . The brake is connected to a 5V high‑level effective through a switch. The front row of wiring terminals are all weak current directly input to the MCU main control, and cannot be touched or touched with high voltage and strong current.

7. When the PWM is input from the 2 ports of the motherboard PG (the built‑in potentiometer on the board is adjusted to the minimum, and the short interface on the board is short‑circuited at the same time as shown in the figure above), the amplitude is 2.5‑5V, and the frequency is 50HZ‑20KHZ.

8. When the external analog 0‑5V input, input from the 2 terminal ports of the main board (the potentiometer on the board is adjusted to the minimum, the wiring is shown by the dotted line in the figure above)

9. Plea

1. Our listing price includes the value of goods,packaging cost,and export taxes,not including international duties.
2. duties,taxes,and charges are not included in the item price or shipping fee.
3. The duties are buyers' responsibility.Please check with your country's customs office determine what these additional costs will be prior to your purchase.
4. All disputes arising from the duties will be submitted to ebay for solution.

1. Any questions, pls. contact us via ebay message or email us.We will reply your message within 48 hours. If you do not receive our reply within 48 hours, pls. post a message again because sometimes our message system may block some emails.

2. If you are satisfied with our service, pls. kindly leave us a positive feedback and give us the Detailed Seller Rating with all "5 " in very area
3. Our aim is to provide Level Customer Service, your recognition will encourage us greatly and serve you better. We strive to keep all our customers satisfy.

We will do our up most to exceed your expectations in customer service, communication and dispatching of your orders.

https://image-us.chengykj.com/upload/third_resource/image/shipc73.jpg