Tial MVR Wastegate includes all springs
Note: Black Wastegate
Car Make: Toyota
Car Model: Supra MKV
Years: 1993-1998
Engine: 2JZ-GTE
Compressor Wheel Inducer: 76mm
Exhaust Wheel Exducer: 85mm
Exhaust Housing A/R: 1.28
Exhaust Housing Inlet: V-Band Stainless
Exhaust Housing Outlet: V-Band Stainless
Compressor Housing: GT42 / Sportsman 5.0" / 3 5/8" V-Band
Material: Stainless Steel (Turbo Manifold)
Center Cartridge: Ball Bearing
Supra 2JZ-GTE Turbo Kit Contains:
01012042.B.SM.S.2.D44 - PHR V45 Equal Length Turbo Manifold for Sportsman V-Band Dual 44mm Wastegates 2JZ-GTE
705-7685-B-NG-R.SS.VB.128.VB - Precision Turbo 7685 Next Gen R Billet Ball Bearing GT42 Sportsman SS V-Brand 1.28 AR V-Band
MVR44-BLK x 2 - Tial MVR 44mm V-Band Black Wastegate
| Material | Stainless Steel |
| Horsepower Rating | 500-1700 |
| Primary Tubing Outer Diameter | 1.9" |
| Primary Tubing Inner Diameter | 1.682" |
| Tubing Material | Schedule 10 Stainless |
| Flange Material | Stainless Steel |
| Primary Tubing Size | 1.5 Schedule 10 |
| Turbine Fitment | Precision Sportsman V-band inlet/outlet |
| Number of wastegates | (D) Dual wastegate |
| Wastegate Flanges | Dual Gate "Tial MVR" 44mm, 45mm or 46mm |
| Collector | Billet |
| Turbo Scroll | Single Scroll |
Features and Solutions
The Powerhouse Of Manifolds
Our manifolds are a key piece on some of the fastest and most beautiful cars on the planet. We hope to be a part of yours.
Equal Length Design
The Powerhouse Racing V45 Turbo Manifold features equal length (and equal volume) runner design. This means that the distance from the exhaust port to the turbo is equal between all 6 runners. This not only produces a heavenly exhaust note that you won't find anywhere else, but also increases overall performance.
The even exhaust pulse helps each runner to scavenge the next pulse and provides consistent exhaust pressure throughout the manifold, at the turbine wheel and at the wastegate. You will find this produces higher peak power, better spool, lower exhaust back pressure, and better boost control.
V-band Turbine Housing
Powerhouse Racing is proud to offer our V45 Turbo Manifold for the 2JZ-GTE engine. It's made to support V-band inlet turbine housing equipped turbos like the Precision Sportsman cover turbos.
23 vs 45 vs 50
You'll notice the second two digits on our manifolds are different (eg: S23 vs S45). What's the difference between the manifolds? Runner size. Below is a chart to help differentiate between manifold runner sizes.
| 2nd Two Digits | Primary Runner Size |
| 23 | 1.25 Schedule 10 |
| 45 | 1.5 Schedule 10 |
| 50 | 1.5 Schedule 10 |
Runner size is an interesting debate. You can think of this in the same manner as Turbine Housing A/R if you are familiar with it. A smaller runner restricts flow, but increases exhaust gas speed. A larger runner increases flow, but decreases exhaust gas speed. Higher runner flow will result in slightly higher peak horsepower, but slightly slower spool. Lower runner flow will result in slightly lower peak horsepower, but slightly faster spool.
The decision on what works best for you is up to how you plan on using your car. If you are trying to maximize horsepower for your turbo, a larger runner may benefit you. If you want better all around power, a smaller runner may benefit you.
None of our manifolds are poor at making horsepower. Our 23 and 45 turbo manifolds both are rated for the same horsepower. UP to 2000 or more if you have a turbo that can do it! The turbo you choose plays a much larger role in the horsepower you can make. The manifold is often better chosen after you decide what turbo you will use and where you want your performance to be.
Our 50 turbo manifolds are reserved for PRO MOD Drag Race Turbo's and paired with a capable turbo, can produce anywhere from 1500hp to over 3000hp!
Installation
PHR equal length manifolds can be a real pain to install, but we have focused on trying to ease the burden of doing so. We have included short studs for our 2JZ-GTE manifolds and provide a flange nut with a smaller flange to sit next to the runners. We have paid careful attention to the area around the stud to make sure it can seat properly and you can get the necessary tools to the nut.
Fitment
PHR builds the best fitting manifolds. Turbo positioning is ideal. We allow for plenty of room for downpipes, and oil drains, and they fit perfectly under the stock supra hood, even with very large turbos.
Some Details
- PHR S and V Series manifolds use schedule 10 stainless steel tubing. Strong material backed by our lifetime warranty against cracking.
- PHR S and V Series manifolds are hand built in-house by some of the best fabricators on the planet. Pain-staking detail is taken in every inch of these.
- All TIG welded, Fully back purged, for strength quality and flow. These also eliminates any crystallization (slag). Slag can break off from inside lesser designed manifolds and damage the turbo.
Billet Collector
PHR was the first to use billet collectors on manifolds for the 2JZ. The introduction of the billet collector makes PHR's manifolds, not only the best performing, but also the most beautiful manifolds in the world.
The billet design makes a solid structure at the collection point, so there are no welds after the runner. The Turbo flange is perfectly flat for better seal, and the finish is next to none.
Maximum Performance
PHR manifolds are used by some of the fastest racers in the world. We take price in designing and producing the highest quality and best performing manifolds on the planet. We have manifolds that work well anywhere from 500hp to over 3000hp!
More than just a manifold
We include more than just a manifold when you get a PHR V45.
Short Stud and Nut Kit
If you've ever installed a turbo manifold on the 2JZ-GTE, you understand the pain it can be. The factory studs were designed with the stock sequential turbos in mind and therefore are not ideal to use with a tubular manifold. They are way too long and become a huge problem when installing a manifold.
PHR remedies the problem by providing our Short Stud and Nut Kit, which features Grade 12.9 Studs, so not only are they shorter, they are much stronger than OEM. The flange nuts also have a smaller diameter flange which allow them to fit better next to the tubular runners.
Lower Waterneck Adapter (Rotator)
The lower waterneck rotator, rotates your waterneck downward, and away from the turbo manifold, giving you extra room you need to install the turbo manifold and turbo. These are essential for clean installs without extra work or welding to get the turbo, manifold or intercooler piping fit properly.
Boost Control
Advertised spring pressure does not always follow real world turbo outlet pressures. Several factors will affect the wastegate openening pressure. Mostly it's pressure on the bottom of the diaphragm and pressure on the bottom of the valve. Pressure on the bottom of the diaphragm is easy, it's really just turbo compressor outlet pressure. Pressure on the bottom of the valve is more complicated.
Manifold design, turbo sizing, turbine size and Turbine housing A/R directly effect pressure on the bottom of the valve. These can all effect exhaust manifold pressure, not only at the turbo but at the gate as well. You can get different pressures in the collector of the manifold and at the bottom of the valve, but in general, they should be fairly close to the same, but even 1 or 2 psi will have an effect. With all of those factors added in, you cannot assume the advertised spring pressure will output actual advertised boost pressure.
A very well designed manifold/turbo combination may produce significantly less exhaust back pressure, which will increase the turbo compressor outlet pressure compared to advertised spring pressure.
All this told, the advertised spring pressure is a good guideline, but the springs will need to be adjusted depending on what testing results we get. Typical Pressure on the PHR Manifolds are usually 5 psi above advertised is what we usually see on Tial wastegates. If you wants lower pressure, say 14, you may need to put a 9 or 10 psi spring combination in.
The most important thing is not what is the advertised spring, but are you able to control the boost to what you want. As long as you are not boost creeping, the wastegates are doing their job.
Precision Turbo 7685 Next Gen R Billet Ball Bearing GT42 Sportsman SS V-Brand 1.28 AR V-Band
Tial MVR 44mm V-Band Black Wastegates
TiAL Sport Inc. USA takes pride in establishing its company reputation by designing the highest quality engineered products for today's performance turbo charging systems market. The production of TiAL Products super alloy based 46mm wastegate was the inception of the company's ability to design, manufacture and deliver to the market a high performance and high quality product at a market competitive price. We are proud to bring to you our USA made, high-performance automotive products. Our main goal is to design, engineer, and manufacture the best possible products. At TiAL Sport we believe there is no room for compromise. We only create innovative designs and produce and deliver the highest level of product integrity. TiAL Sport is looking forward to meeting and exceeding your high performance engine boosting systems needs.
- High temp NiCrFe based alloy is used for valve and 347SS valve housing will offer longer product life compared to competing designs.
- High temperature silicone Nomex reinforced actuator diaphragm.
- 17-7 PH Stainless Steel actuator spring gives consistent pressure at high temperature, resist "relaxing" at temperature to 900F (483C).
- Nitronic 60 Stainless Steel is used for the valve seat, and valve bushing.
- All Stainless Steel hardware.
- Mating weld flanges are 304L
- Color anodized aluminum actuator (Silver, Red, Blue, Purple, Black).
- 3 lower ports and two top ports for easy install, no need to rotate the actuator top at all, plugs included for unused ports.
- Ultra compact design fits in very tight spaces
- V-Band inlet and outlet make install easy, flanges and clamps are in the box!
- Integrated -4 AN water cooling ports that cycle a small amount of coolant through the actuator top to keep the temperatures down in extreme conditions such as road racing. These are leak tested after installation from the factory and can be removed if not utilized.
- Extreme high temp casting available for Motorsport applications
| MV-R | Option |
| Flange Materials | 304L Stainless |
| Pipe Size | Inlet Flange: 1.875" OD Outlet Flange: 1.75" OD |
| Colors | Black |
| Spring Pressures | .2bar to 1.5bar Included |
| Thread | Air Ports (5): M10 x 1.0, Water Ports (2): M8 x 1.0 |
Return Policy: We allow returns of unopened product within 30 days of the purchase date for a money-back refund. If the original packaging is missing or damaged, or if it has been longer than 30 days since you purchased the item, there may be restocking fees incurred. Please message us for a Return Authorization Number before sending anything back to avoid processing delays.
- Best Pricing
- Fast Shipping
- Immediate Response Time
- Experienced in International Export
- 100% Positive Customer Satisfaction Feedback Rating
Most domestic orders ship within 5 days, please allow up to 7-10 days for international orders to ship.
We are very familiar with International Export procedures and we ship out of the country every day. If you are a customer outside of the United States of America, have no worries, we will get your parts to you quickly and correctly, many times just as quickly as our domestic shipments.
Some shipping destinations will require additional shipping, these customers will be contacted immediately after placing their order. Feel free to contact us before placing your purchase for an exact shipping quote.
Import Duties, Taxes, and Charges are not included in the item price or shipping cost. These charges are the buyer's responsibility. Please check with your country's customs office to determine what these additional costs will be prior to bidding or buying.
Quoted shipping does not include insurance. If you would like to add insurance to your contact us here to go over the options.
Please note that eBay requires all orders $750.00 and above to have Signature confirmation, so if your package total is $750.00 or more, your shipment will require a signature.
Even though we are based in Florida, not all orders ship complete from our Florida location. Please be aware that some parts will ship directly from other states to your location. Please message us before clicking buy-now to check location availability if this is a concern of yours.
PLEASE NOTE, ORDERS TO THE FOLLOWING COUNTRIES WILL BE SHIPPED VIA USPS INTERNATIONAL TO AVOID DELAYS AND COMPLICATIONS, UNLESS SPECIFICALLY REQUESTED BY THE BUYER TO SHIP VIA UPS:
- Russia
- Brazil
- Greece
20,000 sqft Facility in Sanford, FL Our new facility is located in sunny Sanford Florida, but we ship all over the world every day with the most competitive rates.
