Feature:

1. Car Battery : Provides a convenient charging solution for both car and motorcycle batteries. Save time and effort with plug and play convenience.
2. Motorcycle Battery : Features multiple safety prevention designs including overcharge, over discharge, short circuit, and overheat prevention for safe use.
3. Portable and Lightweight Design: The car battery is ideal for outdoor travel and emergency situations. Repair old and damaged batteries to extend battery life.
4. LCD Display and Easy Operation: Simple and easy to operate, the LCD screen allows for easy monitoring. Input voltage: 110‑220V 50/60hz, Output voltage: 12V‑14.8V (‑15°C‑45C).
5. Fast Charging: The motorcycle battery adopts fast charging with an output voltage of 12V‑14.8V and peak current output of 6A, suitable for outdoor travel and emergencies.

Specification:

Item Type: Battery
Material: Metal; ABS Plastic
Operating Voltage: 110-220V 50/60hz
Output Voltage: 12V-14.8V (-15°C-45°C)
Output Cable Length: Approx. 65cm/25.59in
Input Cable Length: Approx. 85cm/33.46in
Input Power: 150W
Measured Output Power: 90W
Output Peak Current: 6A

Mode:
Car Mode: Suitable for cars, utility vehicles, trucks, and acid batteries;
AGM/GEL: Suitable for cars with start stop function.
Motorcycle: Suitable for various motorcycles and acid batteries.
Maintenance Mode: For old batteries that have been idle for a long time without charging, you can try the maintenance mode to activate.
Season Mode
Winter: The icon will be displayed at 10°C and below in winter mode.
Summer: The icon will be displayed in summer mode at 28 degrees Celsius and above. Adjust the appropriate charging voltage automatically based on different temperature detections.
Note: Temperature detection is automatic, no need to set. The icon will not be displayed in the constant temperature mode between 10 and 28 degrees Celsius. Temperature detection has some error, but does not affect normal charging.
Repair Mode Operation:
1. Connect the battery, plug in the power, press and hold the "Function Select" for 5 seconds, adjust to "Repair Mode". At this time, the LCD screen will display repair symbol 2h (2 hours), battery 0% 100% alternately flashing. At this time, the repair time is 2 hours. Pressing "Function Select" once can add 1 hour, with a maximum repair time of 12 hours. After adjusting the repair time for 5 seconds, the pulse repair will start.

2. It is recommended to repair the motorcycle battery for about 5 hours, and the car battery is recommended to be repaired for about 8 hours (the longer the battery is not heated, the better the effect).
3. If you need to stop the service, please adjust or disassemble the directly according to the manual
Select Mode.
4. Pay attention to the temperature of the battery when repairing, if there is burn, it should be terminated in advance! The maximum maintenance time is 12 hours, and it will automatically switch to charging mode after 12 hours.
5. The battery can be fully charged after a long service. If the battery shows 100% after switching to charging mode, it means the battery is fully charged. After charging, unplug and check if the power supply is fully charged normally!
How to charge it
1. Check whether the battery parameters match the ;
2. Red clamp battery positive (+), black clamp battery negative (-);
3. After clamping, the LCD screen should light up. The displayed power and voltage indicate that the connection is correct;
4. Connect to the home power supply and the starts charging
5. Select the charging mode that matches your battery
6. When the battery is fully charged. At the same time, the battery voltage is displayed, indicating that the battery is fully charged.
7. Complete charging and remove the .

Troubleshooting common charging issues
1. The is connected to the battery, and the screen does not display the reason: the positive and negative electrodes are not connected correctly, the positive and negative electrodes are clamped incorrectly, or the battery is dead. Solution: First, check whether the positive and negative terminals of the battery are clamped wrongly, check whether the battery has electricity, and check whether the chip is clamped firmly
2. Reason for the alarm beeping sound for a long time: The alarm beeps for a long time Reason: the positive and negative poles are not connected correctly, treatment method: first check whether the positive and negative poles of the battery are clamped wrongly, and then replace the position of the positive and negative pole clamps (if there is no wrong clamp, the positive and negative polarity is reversed, and it is recommended to replace the battery)
3. The battery has no charge or low power, but the reason for the full display is when charging: feeding battery, vulcanized battery, battery with too low voltage, and too long idle time, due to excessive internal resistance of the battery or reduced battery capacity, it reaches the full voltage value instantaneously when charging, and cannot be charged, so it is displayed full!
4. Connecting the battery shows the power but plugging in the power does not work and does not respond Reason: This is no power input. Solution: Check if the 220V power supply has power, try to change a few more sockets!
5. Reason for long term full charge: If the battery is not fully charged for a long time, it is due to the vulcanized power supply of the battery or lack of water, the voltage value cannot be charged, so it will be charged. Solution: If it is hot, stop charging to prevent the battery from bulging. If it's a water battery, check it all the time. This type of battery gets hot when it is charged!

Package List:

1 x
1 x User Manual