300Bar PCP Luftpistole Gewehr Hochdruck Luftpumpe Kompressor Auto Stop Paintball

300Bar Luftpumpe Kompressor Auto Stop Paintball PCP Luftpistole Gewehr Hochdruck

Spezifikationen:
Name: Elektrische aufblasbare Hochdruckpumpe
Vorteile:Gute Kühlwirkung, lange kontinuierliche Arbeitszeit, automatische Abschaltung, Druckeinstellung, Sensor hinzugefügt
Stromversorgung: 220V/50Hz
Strom: 8A-10A
Arbeitsdruck: 0-30 MPA
Verfügbare Kapazität: 0 - 6.8L
Geschwindigkeit: 2800R/Min
Kühlmodus: Wasserkühlung + Luftkühlung
Leistung: 1800W
Kompressionsmodus: sekundäre Kompression
Gewicht: 17kg
Schmiermodus: Ölspritztyp
Größe: 34CM * 37CM ​​* 18CM
Arbeitsgeräusch: 70dB
Nutzungszeit: 6,8l (45 min); 0,5l (5 Minuten); 0,45l (4min); 0,35l (3: 40min)
Hauptanwendungen: Hochdruckprüfung, Flaschen, Automobile

Betriebsmethode der elektrischen Luftpumpe:
☆☆ Kontrollieren Sie die Ölmenge vor jedem Gebrauch, das Öl sollte den roten Punkt überschreiten, aber nicht zu viel. Das Öl, das ins Ausland exportiert wird, wird entnommen und muss selbst hinzugefügt werden.

☆☆ Tauschen Sie den Atemstopfen aus. (Sehr wichtig) Tauschen Sie den für den Transport verwendeten Öldeckel gegen einen streifenförmigen Atemstopfen aus.

☆☆ Um die Wasserpumpe zu installieren, müssen Sie die Wasserpumpe ins Wasser stellen. Je mehr kaltes Wasser, desto besser. Nachdem die Wasserpumpe normal umgewälzt wurde, kann die elektrische Luftpumpe eingeschaltet werden. Manuelles Herunterfahren nach Erreichen des erforderlichen Drucks, der gesamte Prozess erfordert Aufmerksamkeit. und es ist verboten zu gehen.

☆☆ Das mechanische Manometer schraubt den Zeiger direkt auf den gewünschten Druck. Wenn der Druck nach dem Start auf den eingestellten Druck ansteigt, stoppt er automatisch.

☆☆ Lösen Sie die Entlüftungsschrauben auf beiden Seiten, bevor Sie die Maschine starten. (Denken Sie daran, dass die Maschine unter Nulldruck starten muss. Wenn die Entlüftungsschraube nicht gelöst wird beide Seiten normal drücken Nach dem Ende des Aufblasens die entleerte Schraube lösen und dann entleeren, dann die Inflationsverbindung nehmen.

☆☆ Drücken Sie die Taste “SET”, um den gewünschten Druck einzustellen. Drücken Sie "ON", um starten Sie die Maschine. Wenn der Druck auf den eingestellten Druck ansteigt, stoppt er automatisch.

Packliste:
1x Luftpumpe
1x manuell

Air Compressor Tire Inflator 4500PSI Heavy-Duty High Pressure Pump 1800W Motor

Specifications:
Name: Electric High Pressure Inflatable Pump
Advantages:Good cooling effect, long continuous working time, automatic shutdown, pressure setting, added a sensor 
Power supply: 220V/50Hz
Current: 8A-10A
Work pressure: 0-30 MPA
Available capacity: 0 - 6.8L
Speed: 2800R/Min
Cooling mode: water cooling + air cooling
Power: 1800W
Compression mode: secondary compression 
Weight: 17KG
Lubrication mode: oil splash type
Size: 34CM * 37CM * 18CM 
Working noise: 70dB
Use time: 6.8l (45 min); 0.5l (5 min); 0.45l (4min); 0.35l (3: 40min)
Main applications: High pressure testing, bottles, automobiles

Operation method of electric air pump:
☆☆ Check the amount of oil before each use, the oil should exceed the red dot, but not too much. The oil that is exported to foreign countries is taken out and needs to be added by itself.

☆☆ Replace the breathing plug.(Very important) Change the oil cover used for transportation to a strip-shaped breathing plug.

☆☆ To install the water pump, you need to put the water pump into the water, The more cold water, the better, After the water pump is normally circulated, the  electric Air pump can be turned on. Manually shut down after reaching the required pressure,the whole process needs attention. and it is forbidden to leave.

☆☆ The mechanical pressure gauge directly screws the pointer to the required pressure. When the pressure rises to the set pressure after starting, it will automatically stop.

☆☆ Loosen the air bleed screws on both sides before staring the machine,(Remember the machine needs to start under zero pressure. If the bleeder screw is not loosened. the machine will not start. After stating the machine,tighten the Bleed screws on both sides to press normally. After the end of the inflation, loosen the deflated screw and then deflate, then take the inflation joint.

☆☆ Press the "SET" button to set the required pressure. Press "ON" to start the machine. When the pressure rises to the set pressure,it will stop automatically.

Packing list:
1x Air pump
1x manual

PushAuction


Am 06.05.2024 hat der Verkäufer die folgenden Angaben hinzugefügt:

DataCaciques