7 Battery Capacity Checker
• 100% brand new and high quality
Features:
• Compatible device: NiCd, NiMH, LiPo, LiFe, Li-ion
• Use for LiPo LiFe Li-ion NiMH Nicd battery
• Applies to check the batteries
• 2.1" screen display
• Battery Type: NiCd/NIMH,Li-Po,LiFe,Li-Ion
• Cell number: NiCd/NIMH(4-7 Cells),Lithium type(2-7 Cells)
• Display Mode: Battery cell voltages,total voltages,lowest cell voltage, Highest cell voltage gap between highest cell voltage and lowest cell voltage, Remaining battery capacity(%)
• Size: app.8.3cm x 2.5cm/3.26'' x 0.98''
• Color: Black
• Quantity: 1 Pc
• Note: 1.Please allow 1-3mm error due to manual measurement. pls make sure you do not mind before you bid.
2.Due to the difference between different monitors, the picture may not reflect the actual color of the item. Thank you!
• 3.the item is without the battery ,pls note it before you buying it .
Package Included:
• 1 x Battery Capacity Checker
• 18650 Battery Capacity Meter Tester
• 100% brand new and high quality
• Material: Electrical components
• Color: See pictures
• ZB2L3 battery capacity tester discharge type 1.2-12V external load capacity of the battery and other tests 18650
• Tools, single-function, by controlling the load off and get real-time integrated discharge current capacity results
• Maximum support 15V 3A discharged through the discharge voltage and current, itself does not discharge
• Maximum capacity statistics support 9999Ah (9999000mAh)
• Automatically identify and develop appropriate battery termination voltage can also be manually adjusted
　
• Specifications:
• Power supply voltage: DC4.5-6V (micro USB connector)
• Operating Current: less than 70mA
• Discharge voltage: 1.00V-15.00V 0.01V resolution
• Termination voltage range: 0.5-11.0V
• Supported by current: 3.000A 0.001A resolution
• Maximum voltage measurement error: 1% + 0.02V
• Maximum current measurement error: 1.5% + - 0.008A
• Maximum battery capacity range: 9999Ah (1Ah = 1000mAh) greater value by shifting the decimal point to switch, when the display is less than 10Ah X.XXX, as shown above to achieve 10Ah XX.XX, and so on.
• Board size: 50mmX37mm
• Finished Size: 50mmX37mmX17mm (length X width X height maximum position size, contains copper foot height)
　
• Instructions:
• 1. The first test should be fully charged battery.
• 2. Connect the battery to be tested positive to positive input, a negative input to the negative, can not be reversed (with load reversal may damage the circuit)! Load connected to the output of the positive and negative output, to work through the tester micro USB power supply (not available desktop or laptop USB powered), then the battery voltage.
• 3. Direct start test need only one press of the "OK" button, the tester can automatically develop an appropriate termination voltage of the battery full charge voltage, and will start flashing after the test three times. Need to develop artificial termination voltage only when the battery voltage display state by pressing "+" or "-" buttons to modify the termination voltage display beginning with P, behind the representative voltage resolution 0.1V, set up after pressing the "OK "start testing.
• 4. After the start of the test the tester will control the load of the electronic switch is turned on, the test data shows that the process will release capacity (Ah), current discharge current (A) and battery voltage (V) between the wheel was. When the battery voltage reaches the set cut-off voltage, load control switches off the tester display data stays in capacity (Ah) and above and the corresponding indicator flashes quickly together, now displays the actual capacity of the battery is discharging capacity, about the press "OK" to terminate flashing allows stable data display, press again "OK" button to return to the power-on state can just replace the battery test the next section ......
　
• Error codes and their meanings:
• Err1: battery voltage is above 15V
• Err2: battery voltage is lower than the termination voltage
• Err3: Battery can not afford to load or discharge current line too much resistance
• Err4: overcurrent (current exceeds 3.1A)
　
• Note: Use the resistance of the discharge process, resistive load will seriously heat, please pay attention to safety!
• This circuit voltage in order to improve the measurement accuracy, specially designed DC bias, when the terminal displays nothing then a small voltage does not affect the actual measurement, if you are shorting the input terminals (absolute 0V) will show 0
• No retail package
• Quantity:1Pc
• Note: Due to the difference between different monitors, the picture may not reflect the actual color of the item. Thank you!!
Package Included:
1Pc x battery capacity tester1Pc x Load resistor

Car Capacity Tester Battery

Description

100% Brand New And High Quality
Input voltage：8-50V
Input current：5-12mA
Fit for Battery Type: lead-acid/Pb-Acid battery and Lithium battery

• LI 3S / 4S /5S /6S /7S/8S/9S/10S/11S/12S/13S/14S/15S Lead-acid 12V/24V36V/48V
Dimension: please refer to the picture
Using Instruction:
(1) Key operation:
The one white buttons on the back of the indicator are used to select parameters.
(2) Batteries model selection:
1.Power off the indicator
2.Hold key
3.Power the indicator on
4.Release button，then the screen will display symbols in English: "XP" or "XC" ，x is the number of cells, then users can select batteries model by keys in the following order:
P1: Pb12V lead-acid battery
P2: Pb24V lead-acid battery
P3: Pb36V lead-acid battery
P4: Pb48V lead-acid battery
C2: 2 pcs lithium batteries
C3: 3 pcs lithium batteries
C4: 4 pcs lithium batteries
C5: 5 pcs lithium batteries
C6: 6 pcs lithium batteries
C7: 7 pcs lithium batteries
......
C15: 15 pcs lithium batteries
Package included:
1 x Battery Capacity Indicator
1 x 2 Pin Cable