engraving machine parameters

Packing List:

1X main unit (Frame)
1X main unit (working base)
2X Fence baffle
1X control box
1X A axis
1X Sinal cable for A axis
1X pump
1X USB line
2X cutter 2*6mm
2X cutter 3*6mm
10X 4*7mm round head
6X 4*10mm black Inner six angle screw with nut
8X 5*20mm black Inner six angle screw
4X 5*8mm Flat Philip's head screw with nut and gasket
8X 6*24mm BALCK FLAT Inner six angle screw

5. With the assist of the ROUTER 6040T, your design idea will be real-time display.

 

 

 

 

engraving machine parameters:





X, Y, Z Working Area: 600(Y)*390X*120(Z)mm

Outside dimension: 865*680*570mmL*W*H

Table size: 770Y*490Xmm

Lathe structure: 6061/6063 Aluminium alloy

Max. Feeding height: ≤100mm



Drive unit:


X axis---1605 Ball Screws

Y axis---1605 Ball Screws

Z axis---1204 Ball Screws



Sliding unit:


X axis---High intensity Chromeplate shaft

Y axis---High intensity Chromeplate shaft

Z axis---High intensity Chromeplate shaft


Stepping motor: 57 two-phase 3A 150N.cm

 

 
1Water cooled spindle motor can work longer time than air cooled motor.
2Water cooled spindle motor has higher stability and better concentricity than air cooled motor.

Spindle motor

tips1.The spindle motor must connect with the VFD.

2.It cannot directly connect with the supply voltage (AC220V).

3.Please don’t change the data setting of the VFD if you are not professional technicians, or it might damage the spindle motor.

Outside dimension: 65*158mm

Material: 304 stainless steel, Copper coil, Pressure cast aluminum pipe water jacket

VOLTS, current,power: AC220V, 50Hz,5A,1.5 KW VFD;

Spindle motor: 1.5 KW water cooled

Spindle speed: 24000 rpm

Max working frequency: 400Hz

Principal axis collet: ER11collet,Standard configuration :6mm

Nut Model: ER11-A

Cooling: Water-cooling

Speed mode: By adjusting the VFD output voltage and operating frequency from 0-24000RPM

Lubrication way: lubricated by high grease

 

Repeat accuracy: 0.05mm

Spindle precision: radial beat acuities 0.03mm

Carving Instructions: G code / TAB files / nc file / NCC files

Communication interface: through USB connection with computer

environment: windows XP / win7 32bits system

Working Speed: 50-1500mm / min (different material with different speed settings)

Maximum Idle speed: 0-1500mm/min

 

 

 

 

 

 

Control box parameters:

 

Operating Voltage: AC220V

Control unit: Toroidal transformer + PWM power supply module + TB6560 stepping motor drive

Computer connection: USB port

Command code: G code

Acceptable software: , EMC2

Protection: Emergency stop button

 

 

 

 

Feature:

 

1. The NEW 1.5KW water-cooled VFD is available operating for long time,which can reinforced
the processing abilty of the machine and can be used toprocess aluminum alloy and hard wood.

2.water cooling spindle works more stable and durable.

3. High quality accurate ball Screws drive make the engrving more precision.Anti-blackflash,high precision,long life circle.

 

 

 

How to Use:

1. Assembling and locating the machine on steady desk well.

2. Make sure that your computer has a 25pin USB port output.

3. Place the contral box in a ventilated dry place where there is no dust,no moisture

4. Connecting the control box with the machine and you computer and make sure the plug will not come off.

5. Correctly connect the machine with the controller. Don't suspended the cable which connect the Spindle motor with axis(X,Y,Z,A).Otherwise. It will damage the driver of the controller.

6. Correctly instal the Spindle motor and the heat pump. The heat pump should be covered completely in the water, then turned on the electric current to check whether the water-cooling system working well.

7. Installing a control software and Drive on your computer.

8. Fllowing our manual or guideline to set uo the software.

9. Before turn on the machine, please check all the cable and water- cooling system to make sure they are working fine.

10. You can enjoy making you dream with using our machine now.