12V Mini-Gen Max With Switch For Motorized Bicycle Lighting
Now you can get a reliable lighting system for your 2 cycle motorized bicycle by using
this Mini-Generator MAX designed for 12 to 14.4 volt lighting systems. This item is
designed to be affixed to a 2 cycle motorized bicycle to provide a self sufficient and
dependable lighting system. This item includes a SPDT Light Switch and is easily
installed. Instructions for installation are included.
The Mini-Generator MAX is a
small electrical unit designed to be mounted inside the engine's magneto case to produce
electricity to the Mini-Charger which charges the batteries, or it can be used to produce
lighting (up to 10 watts recommended) directly .
This "Mini-Gen-Max" is designed to
produce more power than our regular Mini-Gen, and is suitable for all 12 volt lighting
systems. This generator will run a lower 3 or 5 watts lights, but is suitable for 10 watts
halogen lighting and other similar headlights. Just install into magneto case using the 2
rear magneto screws and route red (output) wire through wire harness. The red wire from
the Mini Generator MAX will send electricity to your lights through a light switch or
connected directly for continuous light. For a more stable lighting system you can add a
Mini-Charger and battery pack available in our store (links on left side).
NOTE:Please feel free to inquire about pricing for any single item(s).
|
- This Mini-Gen Max is easily installed and includes installation instructions and
precautions.
- A light switch is included for connection to lights.
- This will produce over 12 volts AC at about 1300 RPM or driving speeds of about 12 to
15 MPH.
- Volts can reach up to 18 or more @ 1.5 amps or more during high speeds.
- The SPDT switch includes an optional ground wire for neutralizing the Mini-Gen when
lights are off; resulting in smoother transaction.
- Mount the switch on upper frame rail, handle bar or where ever you
wish.
Note:Mini-Gen wire is approx. 12" long and switch wires are approx. 6"
long. No extra wire included.
- Click on the links on the left to check out our other items.
|
- Just remove the engine magneto cover, then use the 2 rear screws to attach Mini-
Generator inside engine magneto case.
- Remove wire grommet at the front (white plastic or black rubber) then insert Mini-Gen
wire into grommet.
- Use a pick or small screwdriver or nail to push into the area where wire will fit,
then insert wire.
- Instructions and precautions are included for Mini-Gen installation.
- NOTE: The Mini-Gen in this photo does NOT represent the Mini-Gen MAX but only the
positioning of the wire.
|
- After the Mini-Generator is installed, the power wire should be routed toward bicycle
seat post for Mini-Charger connection, unless it's being used for other purpose.
- Position wire inside case away from moving parts and also make sure it will not be
pinched under the cover.
- Use duct tape (any color) or cable ties to secure wire onto bike's bottom bracket and
seat post.
- The Mini-Gen in this photo is connected to the red wire coming from the Mini-Charger.
Your results will look far better than this one.
- NOTE: The Mini-Gen in this photo does NOT represent the Mini-Gen MAX but only the
positioning of the wire.
|
- Here is the Mini-Gen-Max voltage being measured at approx. 1300 rpm's (normal driving
speed = 1100 tp 1800 RPM).
- The magneto in this photo looks stationary because camera flash was used, but it's
actually spinning.
- # This is called a generator (which technically produces dc voltage), but this
produces AC voltage.
- The engine speed here is around 1300 to 1350 RPM which is just around driving speed.
- Most riders will produce this voltage at a speed of around 15 to 18 MPH.
- Higher voltages of around 18 or more is obtainable at much higher engine speeds, but
12 volts is specified as the average voltage.
|
- The Mini-Gen is seen here hooked up to a common 12 volt 10 watts halogen headlight.
- This type of lighting draws around 860 milliamps on a fully charged 12 volt battery
and uses less ac amps due to the nature of ac current.
- Here in the photo you see the light using a little over 700 milliamps at around 1300
rpm.
- Unlike most LED lights, regular light bulbs will run off both AC and DC voltage with
no problem.
- A complete 14.4 Volts Lighting System Will be available in our store very soon if not
already available.
- Caution: Avoid revving up the engine with lights on because high revs of
3000 rpm for more than 5 seconds can immediately blow the bulbs. High speeds while driving
is O.K.
|
PAYMENTS Payments for auction items are expected
within 3 days, but no later than 7 days. All payments accepted through Paypal or CIP.
Serious inquiries about payment for individual items welcome. |
SHIPPING Flat rate shipping & handling price
is available
for the continental USA. Shipping & handling might also be the same for other states
outside the
continental United States. This item will normally ship within 2 business days,
but could take up to 5 business days. To check shipping and handling fees to your state
just click on the SHIPPING AND PAYMENTS button below top photo on this eBay page.
Items will be shipped to the address provided for transaction. Request to change shipping
address after item is shipped will be ignored.
We reserve the right to refuse shipment
to uncomfirmed addresses in which case buyer will be refunded. INTERNATIONAL
shipment is available with
slightly higher fees. To check shipping and handling fees to your country just click on
the SHIPPING AND PAYMENTS button below top photo on this eBay page. |
WARRANTY & RETURNS The SUPER DYNO Lighting
System (patent pending) is warrantied for 7 days cash back, and 30 days replacement. If
you
are unsatisfied for any reason, just return the complete kit, and a refund will be issued
(less shipping and handling). Shipping & handling is not refundable, and the customer
is
responsible for shipping cost of the returned item.If any problems are experienced with
our products, please contact us for assistance before resorting to any other course of
action.
NOTE- Any item showing signs of
tampering or abuse will void warranty!
INTERNATIONAL customers are legible
for the 30 days parts replacement warranty ONLY. Customer is responsible for shipping
returned items. |
DISCLAIMER This "SUPER DYNO Lighting System",
and all
parts, pieces, ideas and designs associated therewith, are the proprietary rights and
ownership
of Wonderful Creations Store. Any copying, modifying, tampering and or false claims are
discouraged and expressly prohibited. By purchasing this system you agree to abide
by
any and all traffic laws governing your city, state or country and further agree to hold
Wonderful Creations and any associates thereof, blameless for any accidents, mishaps,
property loss,
damages, death, injuries or expenses reportedly, or supposedly caused by the use, or
misuse
of this lighting system. |
