|
6V Mini-Generator For 2 Cycle Pull Start Bike Engines
Now you can get a reliable
lighting system for your 2 cycle motorized bicycle by using this
Mini-Generator designed for 6 volt lighting systems. This particular Mini-Gen item is
designed especially
for pull start 2 cycle motorized bike engines. Like our regular 6 volt Mini-Gen, this will
provide a self
sufficient and dependable lighting system. The Mini-Generator is a small electrical unit
designed to be
mounted inside the engine's magneto case to produce electricity to the Mini-Charger which
charges the
batteries, or it can be used to produce lighting (up to 5 watts recommended) directly
. This "Mini-Gen"
is designed to produce AC voltage of 6 or more (nominal) for regular 6 volt 3 watt
lighting that's normally
used with bicycle dynamo. Just install into magneto case using the 2 rear magneto screws
and route red
(output) wire through wire harness. The red wire from the Mini Generator will send
electricity to your lights
through a light switch or connected directly for continuous light.
|
- This Pull Start Mini-Gen is easily installed and includes installation instructions
and precautions.
- Just remove the engine magneto cover, then remove the pull starter cog and use the 2
rear screws to
attach Mini-Generator inside engine magneto case.
- Remove wire grommet at the front (white plastic or black rubber) then insert
Mini-Gen wire into grommet.
- Use a pick or small screwdriver or nail to push into the area where wire will fit,
then insert wire.
- This will produce over 6 volts AC at about 900 RPM or driving speeds of about 12 to 15
MPH.
- Volts can reach up to 12 or more @ 1.2 amps or more during high speeds.
- If running lights directly from Mini-Gen, avoid revving engine with lights on to avoid
blowing out
lights. High speeds while driving is O.K.
|
- Remove wire grommet at the front (white plastic or black rubber) then insert Mini-Gen
wire into grommet.
- Use a pick or small screwdriver or nail to push into the area where wire will fit,
then insert wire.
- Just temporarily install nut and turn the pull starter cog to make sure there is no
rubbing on the
Mini-Gen.
- Instructions and precautions are included for Mini-Gen installation.
- This will produce over 6 volts AC at about 900 RPM or driving speeds of about 12 to 15
MPH.
- Volts can reach up to 12 or more @ 1.2 amps or more during high speeds.
- If running lights directly from Mini-Gen, avoid revving engine with lights on to avoid
blowing out
lights. High speeds while driving is O.K.
|
- After the Mini-Generator is installed, the power wire should be routed toward bicycle
seat post for
Mini-Charger connection, unless it's being used for other purpose.
- Wire inside engine case should be positioned away from moving parts and also make
sure it will not be
pinched under the cover.
- Use duct tape (any color) or cable ties to secure wire onto bike's bottom bracket and
seat post.
- The Mini-Gen in this photo is connected to the red wire coming from the Mini-Charger.
Your results will
look far better than this one.
- NOTE: For pull starter 2 cycle engines, run engine for about 10 seconds then remove
cover and check to
make sure there's no sign of pull starter cog rubbing on Mini-Gen.
|
PAYMENTS Payments for auction items are expected
within 3 days, but no later than 7 days. All payments accepted through Paypal or CIP.
Serious inquiries about payment for individual items welcome. |
SHIPPING Flat rate shipping & handling price
is available
for the continental USA. Shipping & handling might also be the same for other states
outside the
continental United States. This item will normally ship within 2 business days,
but could take up to 5 business days. To check shipping and handling fees to your state
just click on the
SHIPPING AND PAYMENTS button below top photo on this eBay page. Items will be shipped
to the address
provided for transaction. Request to change shipping address after item is shipped will be
ignored. We
reserve the right to refuse shipment to uncomfirmed addresses in which case buyer will be
refunded. INTERNATIONAL shipment is available with
slightly higher fees. To check shipping and handling fees to your country just click on
the SHIPPING AND
PAYMENTS button below top photo on this eBay page. |
WARRANTY & RETURNS The SUPER DYNO Lighting
System (patent pending) is warrantied for 7 days cash back, and 30 days replacement. If
you
are unsatisfied for any reason, just return the complete kit, and a refund will be issued
(less shipping and handling). Shipping & handling is not refundable, and the customer
is
responsible for shipping cost of the returned item.If any problems are experienced with
our products, please
contact us for assistance before resorting to any other course of action. NOTE- Any
item showing signs
of
tampering or abuse will void warranty! INTERNATIONAL customers are legible
for the 30 days parts replacement warranty ONLY. Customer is responsible for shipping
returned items. |
DISCLAIMER This "SUPER DYNO Lighting System",
and all
parts, pieces, ideas and designs associated therewith, are the proprietary rights and
ownership
of Wonderful Creations Store. Any copying, modifying, tampering and or false claims are
discouraged and expressly prohibited. By purchasing this system you agree to abide
by
any and all traffic laws governing your city, state or country and further agree to hold
Wonderful Creations and any associates thereof, blameless for any accidents, mishaps,
property loss,
damages, death, injuries or expenses reportedly, or supposedly caused by the use, or
misuse
of this lighting system. |
|