Ship from USA to USA, Ship from China to Other Countries!
Name: Dental LED Curing Equipment
Battery (rechargeable use): Lithium ion battery
Battery capacity: 1600mAh
Battery voltage: 3.7V
Weight: about 400g with packaging
Applicable temperature/humidity: 5°C~40°C/≤80%
Packing specification: 300x150x60 mm
Curing time:3s,5s,10s,15s,20s
Charger input voltage: 100V-240VAC, 50-60HZ
Output voltage: host dc 5v/1A
LED light wavelength: 458.5nm
Atmospheric pressure: 50kPa〜106kPa
Light Intensity
P1 Highlight Mode 1800-2200mw/cm2
P2 Standard Model 1000-1300mw/cm2
Note:
The time required for resin curing mainly depends on the resin brand, curing depth and area, etc., 3 seconds is a reference value, not an absolute value, respectfully.
Operation method:
1 Lightly press the "M" mode setting button of the main unit, you can select any of the following two modes to enter the working state:
(1) P1 high light intensity mode: 1800-2200mw/cm2
(2) P2 standard mode: 1000-1300mw/cm2
After selection, the display shows the corresponding characters (P1/P2).
2 Tap the "T" time setting button of the host to set the light curing time:
(1) P1 mode can choose 3 or 5 seconds timing time
(2) P2 mode can choose the timing time of 10, 15, 20 seconds
3. When in use, put the disposable film cover on the head of the main unit, then aim the light source at the position to be cured, press the "" on/off key, the main unit will emit a beep, the main unit will emit blue light and press the selected Working in working mode, the display screen starts to display the countdown time from the selected timing time, and ends at 0 o'clock, and the display screen returns to display the original set timing time.
4. During the work process, you can press the " on/off
"to end the work at any time, and the display will return to the original set timing time.
5. After one irradiation cycle is over, you can immediately press the "on/off" key to start the next cycle. If it is obvious that the handle starts to get hot, stop working until the handle is completely cooled down before starting to work. In P2 mode, it is recommended that the continuous irradiation time does not exceed 120S.
6. Low-voltage indication: The host has a low-battery detection function. When a low battery is detected, the display flashes. Please charge it in time.
7. Connect the power adapter (optional) to the 100V-240V network power when charging, and insert the output end of the adapter into the charging port at the bottom of the host, and the display scrolls.
8. After use, please remove the disposable film cover from the head of the main unit and throw it into the trash can. Repeated use is prohibited. If the lens is stained with resin, please wipe it clean with cotton cloth to avoid affecting the light intensity.
9. The machine will automatically shut down after 2 minutes of inactivity, please press any key to turn it on.
Use and safety precautions:
1. When using the machine for the first time, please charge it for at least 4 hours. The display scrolls when the battery is charging, and the display stops scrolling when it is fully charged. At this time, you can pull out the plug of the power adapter. Long-term charging is prohibited.
2. When in use, a disposable film cover should be inserted and repeated use is prohibited to prevent cross-infection.
3. In clinical use, the light source should be directly irradiated on the cured resin material to prevent improper irradiation position and affect the curing effect.
4. The original shading plate must be used to effectively prevent blue light from damaging the eyes. Blue light is strictly forbidden to irradiate the eyes.
5. Please use the original power adapter, other power adapters may cause damage to the lithium battery and control circuit.
Features for Dental LED Curing Lamp
1. Wireless
2. USB
3. TWO working models: P1 Highlight Mode,P2 Standard Model
4. Time setting: P1:3, 5, P2:10, 15, 20s
5. Large capacity battery, A full charge can be used for more than 500times
Including:
Host
Shading sheet
Date line
No charging stand
510(K) Number: K192233
Regulation Number: 21 CFR 872.6070
Product Code: EBZ
FDA Statement:
The sale of this item may be subject to regulation by the U.S. Food and Drug Administration and state and local regulatory agencies.
If so, you can bid on this item only if you are an authorized purchaser.
If the item is subject to FDA regulation, I will verify your status as an authorized purchaser of this item before shipping of the item.
FDA for Curing Light: 510(K) Number: K192233, Regulation Number: 21 CFR 872.6070, Product Code: EBZ
FDA for Handpiece: 510(K) Number: K181691, Regulation Number: 872.4200, Classification Product Code: EFB, Subsequent Product Code: EGS
FDA for Scaler: 510(K) Number: K163414, Regulation Number: 872.4850, Product Code: ELC
We commited ourselves to your 100% satisfaction both with our goods and services.
1. Please leave me FIVE star POSITIVE feedback if you are satisfied with our items.
2. Please CONTACT me immediately before leave us neutral feedback or negtive feedback, We will try our best to resolve any problem for you untill you are satisfied.
Notice:
1. Import duties, taxes and charges are not included in the item price or shipping charges. These charges are the buyer’s responsibility.
2. Please check your country’s customs office to determine what these additional costs will be prior to bidding/buying.
Warmly remind:
Pls let me know before taking any action, because your action will has an important impact on our shop.
So pls give me a chance to offer the best sollution for you!!
Our working time:
Monday - Friday 9:00 AM - 5:30PM (Beijing)
Return & Refund:
Return within 30 days is accepted, though the item in good condition.