eBay

Introduction:

1.Technical specifications：

1.1Dimensions: 25mm×25mm×240mm

1.2 Net weight: 280g

1.3 Power source

1.3.1 Power supply: rechargeable Lithium battery

1.3.2 Battery mode: ICR 18490

1.3.3 Battery voltage and capacity: 3.7V/ 1400mAh,Battery has protection against Over-voltage, over-current and short circuit.

1.3.4 Adapter Power Input: 100V to 240V, 50Hz/60 Hz Input Power: 10VA Power Output: DC5V/1A

1.4 Light source:

1.4.1 5W high power blue light LED

1.4.2 Checking method: the LED light is fine when the light is on during operating correctly.

1.4.3 The wave length of this product can match with the clinical dental resin solidification, such as 3M, etc.

1.4.4 Wave length: 440nm-480nm

1.5 Light intensity:

P1 mode 2200-3200mW/cm²

P2 mode 1600mW/cm²~2200mW/cm²

P3 mode 1200mW/cm²~1600mW/cm²

2. Operation：

2.1 Press the mode button. Following two modes are available.

2.1.1 TURBO Mode: screen shows P1, Press the time button to select of time which could be 1 and 3 seconds.Its output light intensity is about 3200mW/cm²

2.1.2 NORMAL Mode: screen shows P2, Press the time button to select of time which could be 5,10 ,15and 20 seconds.Its output light intensity is about 2200 mW/cm²

2.2 During the operation, put the disposable sleeve on the top of the main unit, aim the top at the correct position, press the ON/OFF button and the main unit will produce "Bi" sound, the curing light radiates blue light and starts working according to the set modes. Meanwhile, it starts counting down and will produce tone at every 5 seconds, it stops working when counting down to "0".

2.3 During operation, the blue light can be stopped by press the power button at any time.

2.4 After a working cycle, operator can press the ON/OFF switch to start another working cycle. Stop operating if the equipment began to heat obviously, do not restart until the equipment cool down. Suggest continues working cycle less than 10 times.

2.5 Low power detective circuit is fixed inside of the main unit, when low power is detected, the display screen of main unit will wink, please charge in time.

2.6 When the battery needs to be charged, connect the plug of the adapter into the AC100V~240V power supply. Then connect the output plug of the adapter to the DC 5.0V input plug of the pedestal, and then the logo turn to blue. Put the main unit to the charging point of the pedestal, the display screen turn to scrolling display, and the curing lights starts charging.

2.7 After operating, take off the disposable sleeve and throw away, forbidden to reuse.

2.8 This equipment will turn off automatically if don't any action within 2 minutes, turn it on by press any button.

2.9 The depth of solidification of composite is no less than 2mm per 1 second.

Material:The handle is made of plastic，The lamp holder is made of metal

Shipping

The goods you odered will be posted out in the second working day after the paymet has been made. (We will inform you via email if any delay occured due to holiday events.

General shipping time is between 7-12 working days. (After the shipping started, the order will be monitored and the track of the item will be posted on paypal.

Payment

We accept PayPal only.
（The address in your paypal details will be used as the actual shipping adress, please make sure the adress is correct.）

If you are planning on combining your items, please make sure that you wait until ALL auctions have ended before you visit the checkout. All items must be paid within 7 days.

Feedback

You feedback is VERY important to us!

Please leave us positive feedback, an positive feedback will be automatically left for you once we receive your full payment. Please leave us with any concerns prior to leave negative feedback, as we can only correct issues when we are aware of them. We understand the concerns and frustrations you might have, and will try our best to resolve the isuues.

Returns

Exchanges are offered for items that are defective or damaged when received, although this is highly unlikely. After exchanges are made and have not resolved the issue, we will refund the cost of the merchandise.

Defective items or problems with your order must be reported within 3 days after receiving. Please keep all packaging, documentation, packing list, etc. that came with your order. These will be used to verify claims if there is any problem with you.

Restocking fee will be charged for returned items without original package or any quality problem.Please contact us for details before returning your package to avoid misunderstanding.

IMPORTANT: Customer's item must be returned to our facility with the ROF (Return Order Form) at the buyers' shipping expense.

Serivce is our #1 priority at Dentistclub!

If you contact us immediately after placing the order, we will make every effort to assist you with your change request. Unfortunately, we can not make changes or cancel an order once it has shipped.

We offer the best items at the best prices. We strive to exceed all your expectations and put a smile on your face. Your experience will be a pleasant and effortless one when you buy at Dentistclub. We stand behind our products and pride ourselves on OUTSTANDING customer service. We guarantee that you will be delighted with your purchase or we will gladly and promptly issue you a refund or make things right!

FDA Statement
FDA Statement: The sale of this item may be subject to regulation by the U.S. Food and Drug Administration and state and local regulatory agencies. If so, do not bid on this item unless you are an authorized purchaser. If the item is subject to FDA regulation, I will verify your status as an authorized purchaser of this item before shipping of the item. Seller name:Dentistclub City,State:SHENZHEN,China Telephone number:0755-3889136