You may also like
Features:
1.The UBEC is an advanced switching regulator with over-current and over-heat protection function, and the maximum efficency of the system is nearly 90%.
2.The small size and the light weight make it very convenient to use.
3.The comparison of linear BEC and swh-mode BEC: when using a Lithium battery pack more than 3S, a switch-mode BEC has mch higher efficiency than linear BEC.
4.Dont worry about the polarity of battery pack. If the polarity is not correct, the UBEC can't work, but it will not be destroyed. What you need to do is just swap the battery pack polarity
5.A shield covers almost all the electronic components on PCB, and a ferrite ring is attached with the output wires to decrease the electromagnetic interference.
Descriptions:
Why do you need UBEC?The UBEC is a switch-mode DC regulator separated from ESC(Esc--electronic Speed Controller for brushless/brushed motor), it will take high-voltage (5.5V to 26v)power from your battery pack and convert it to a consistent safe voltage for your receiver, gyro and servos.
For traditional speed controller with a built-in BEC, it will very likely have only a limited ability to supply power to your receiver and servos without over heating. If you are using a high-voltage battery pack or have heavy servo load, you should consult the ESC specifications to determine what the stated recommendations or limitations are. In general, ifyou are using a 4 cells lithium battery pack, or more than a 12 cells Nickel based battery pack,you should consider using an UBEC because in such a case the built-in BEC of the ESC can support only 2 servos, which means it is not suitable for RC helicopter and big aircraft.
Item name:3Amp Switch-Mode UBEC
Output:5V/3A and 6V/3A switchable
Ripple:＜50mVp-p(@2A/12V)
Input:5.5V-26V(2 to 6 cells Lipo battery pack,5 to 18 cells NiMH battery pack )
Size: 43x18x6.5mm
Weight:11g
Package information:
Package size:12*8*2cm
Package weight:20g
OPP bag package
Note:
Only the above package content, other products are not included.
1.Due to the difference between different monitors,the picture may not reflect the actual color of the item. We guarantee the style is the same as shown in the pictures.
2.Due to the manual measurement and different measurement methods, please allow 1-3mm deviation.Thanks!
1.The UBEC is an advanced switching regulator with over-current and over-heat protection function, and the maximum efficency of the system is nearly 90%.
2.The small size and the light weight make it very convenient to use.
3.The comparison of linear BEC and swh-mode BEC: when using a Lithium battery pack more than 3S, a switch-mode BEC has mch higher efficiency than linear BEC.
4.Dont worry about the polarity of battery pack. If the polarity is not correct, the UBEC can't work, but it will not be destroyed. What you need to do is just swap the battery pack polarity
5.A shield covers almost all the electronic components on PCB, and a ferrite ring is attached with the output wires to decrease the electromagnetic interference.
Descriptions:
Why do you need UBEC?The UBEC is a switch-mode DC regulator separated from ESC(Esc--electronic Speed Controller for brushless/brushed motor), it will take high-voltage (5.5V to 26v)power from your battery pack and convert it to a consistent safe voltage for your receiver, gyro and servos.
For traditional speed controller with a built-in BEC, it will very likely have only a limited ability to supply power to your receiver and servos without over heating. If you are using a high-voltage battery pack or have heavy servo load, you should consult the ESC specifications to determine what the stated recommendations or limitations are. In general, ifyou are using a 4 cells lithium battery pack, or more than a 12 cells Nickel based battery pack,you should consider using an UBEC because in such a case the built-in BEC of the ESC can support only 2 servos, which means it is not suitable for RC helicopter and big aircraft.
Item name:3Amp Switch-Mode UBEC
Output:5V/3A and 6V/3A switchable
Ripple:＜50mVp-p(@2A/12V)
Input:5.5V-26V(2 to 6 cells Lipo battery pack,5 to 18 cells NiMH battery pack )
Size: 43x18x6.5mm
Weight:11g
Package information:
Package size:12*8*2cm
Package weight:20g
OPP bag package
Note:
Only the above package content, other products are not included.
1.Due to the difference between different monitors,the picture may not reflect the actual color of the item. We guarantee the style is the same as shown in the pictures.
2.Due to the manual measurement and different measurement methods, please allow 1-3mm deviation.Thanks!