• Compatibility :
  •  
  • 2003-2006 Infiniti FX35 3.5L 2003-2008 Infiniti FX45 4.5L 2003-2007 Infiniti G35 3.5L 2006 Infiniti M35 3.5L 2006-2010 Infiniti M45 4.5L 2003-2006 Nissan 350Z 3.5L
  •  
  • Features:
  •  
  • Fits for 2003-2007 Infiniti G35 3.5L Downstream o2 Oxygen 02 Sensor X2

    Compatibility :

     

    2003-2006 Infiniti FX35 3.5L
    2003-2008 Infiniti FX45 4.5L
    2003-2007 Infiniti G35 3.5L
    2006 Infiniti M35 3.5L
    2006-2010 Infiniti M45 4.5L
    2003-2006 Nissan 350Z 3.5L

     

    Features:

     

    • Porous PTFE Filter - Allows atmospheric oxygen to enter the sensor without permitting water or engine contaminants to seep into the casing.
    • Double Protection Cover - Maintains proper unit temperature for quicker response times and protects the ceramic element against silicone and lead poisoning.
    • Stainless Steel Housing - Resists corrosion and contamination with a rugged, watertight body.
    • Aluminum-Oxide Trap Layer - Keeps silicone and lead outside the ceramic elient through, preventing damage to the platinum electrode.

     

    Where is the oxygen sensor in your vehiche?

     

     

    Whow to install an oxygen sensor?

     

    1.Locate the oxygen sensor on your vehicle by looking for a part that looks like a spark plug that sticks out from the exhaust pipe. It will have an electrical connection attached to it.

    2.Disconnect the electrical connection on the oxygen sensor. Use a flat tip screwdriver to push in the tabs and pull the connection apart.

    3.Unscrew the oxygen sensor off the exhaust pipe using either an open-end wrench or a special socket made to remove it. The majority of oxygen sensors will take an SAE 7⁄8 inch (2.2 cm) wrench.

    4.Compare your new oxygen sensor to the old one. If the new one did not come with an electrical connection, but just with the wires stubbed out, you need to do a little work.

    · Cut off the old connector from the bad oxygen sensor, strip the wires and solder the wires to the new oxygen sensor. You can also use butt connectors.

    · Use heat sensitive shrink tape to seal the connections.

    · Follow manufacturer's instructions to know which wires to tie together.

    5.Reverse the steps used in removing the oxygen sensor and install the new part.Add a small amount of anti-seize to the threads of the new sensor. Screw it in place clockwise and snug it down with the socket or open-end wrench. Do not over tighten the sensor as you might strip the threads.

    6.Plug the electrical connections back in.

    7.Turn on the ignition key, but do not start your vehicle. Use the diagnostic scanner/reader to clear the code from the vehicle's computer.

     

    8.Start the car. You should notice an immediate improvement.

     

    NOTE:

     

    If you can't  determine whether the oxygen sensor fit your vehicle or not, please contact us.

     

     

     

     

     

     


    Item Specifics
    Brand gdcarpartsin
    Manufacturer Part Number G831838SIN
    Manufacturer Warranty 1 Year
    Fitment Type Direct Replacement
    Custom Bundle Yes
    Modified Item No
    Type Oxygen Sensor
    Number of Pieces 2
    Wire 4, 4
    Position Downstream
    Custom Bundle Yes
    Housing Material Metal
    Thread Size 18 X 1.5 MM
    Universal Or Specific Fit Specific
    Automotive Color / Finish Steel
    Terminal Type Blade
    Attachment Method Screw-On
    Output Signal Range (V) 0.2 To 0.8 Volt
    Type Sensor
    Features Direct Fit

    Shipping
    1. Orders processed within 24 hours of payment verification.(if you want cancel orders or change address pls contact us within 6 hours after payment,or we are not responsible for shipping a replacement.)
     
    2. We only ship to confirmed PAYPAL addresses. Your PAYPAL address must match your Shipping address.
     
    3. Fast shipping:All our packages use USPS First Class/UPS/Fedex... Package Service
     
    4. If you have not received your shipment within 15 days from payment , please contact!
    Return
    1. You have 30 days to contact us and 10 days to return it from the date it was received. If this item is in your possession more than 7 days, it is considered used and we will not issue you a refund or replacement. There are NO EXCEPTIONS!
     
    2. All returned items must be in the original packaging and you must provide us with the shipping tracking number, specific reason for the return, and item custom lable.
     
    3. We will refund your full winning bid amount, upon receipt of the item in its original condition and packaging with all components and accessories included, AFTER both Buyer and Seller cancel the transaction from eBay. OR, you may choose to have a replacement.
     
    4. Return shipping is to be paid by the Buyer
    Feedback
    We strive for 100% customer satisfaction! FEEDBACK IS VERY IMPORTANT TO US.
    We request that you contact us immediately BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concerns. 
    Payment
    1.We only accept PayPal.
     
    2.Please do not use the PayPal note field to indicate us to ship to other address. The note there will NOT be read. If you want to change the shipping address, please contact us by eBay messages.
     
    3.(if you want cancel orders or change address pls contact us within 6 hours after payment,or we are not responsible for shipping a replacement.)
     
    4.Payment must be received within 10 days as auction ended or order might be delayed.
    Warranty
    1,We stand behind every product we sell.
    2,All of our brand new items come with a 60-Days money-back guarantee.
    3,We define the item as defective only if it doesn't function as described.
    4,It is the buyer's responsibility to understand the item description before bidding.
    5,We will replace the defective items, provided that they are in stock within the warranty period posted with the listing and the buyer return the  original item and pay for the S&H cost for the replacement.
     6,We  will refund the purchase price if the replacement is not available or buyer  prefers a refund and send the original item back at his/her own cost.
    7,Shipping & handling cost are not refundable.
    8,Man-made damage by  abuse or wrong operation is not covered by this warranty.
    9,No  product liability insurance is assumed.

    Shop Category
    Delivery
    Help & Info
    Payment Policy
    Shipping Policy
    Return Policy
    FAQ
    About Us
    Fits for 2003-2007 Infiniti G35 3.5L Downstream o2 Oxygen 02 Sensor X2

    Compatibility :

     

    2003-2006 Infiniti FX35 3.5L
    2003-2008 Infiniti FX45 4.5L
    2003-2007 Infiniti G35 3.5L
    2006 Infiniti M35 3.5L
    2006-2010 Infiniti M45 4.5L
    2003-2006 Nissan 350Z 3.5L

     

    Features:

     

    • Porous PTFE Filter - Allows atmospheric oxygen to enter the sensor without permitting water or engine contaminants to seep into the casing.
    • Double Protection Cover - Maintains proper unit temperature for quicker response times and protects the ceramic element against silicone and lead poisoning.
    • Stainless Steel Housing - Resists corrosion and contamination with a rugged, watertight body.
    • Aluminum-Oxide Trap Layer - Keeps silicone and lead outside the ceramic elient through, preventing damage to the platinum electrode.

     

    Where is the oxygen sensor in your vehiche?

     

     

    Whow to install an oxygen sensor?

     

    1.Locate the oxygen sensor on your vehicle by looking for a part that looks like a spark plug that sticks out from the exhaust pipe. It will have an electrical connection attached to it.

    2.Disconnect the electrical connection on the oxygen sensor. Use a flat tip screwdriver to push in the tabs and pull the connection apart.

    3.Unscrew the oxygen sensor off the exhaust pipe using either an open-end wrench or a special socket made to remove it. The majority of oxygen sensors will take an SAE 7⁄8 inch (2.2 cm) wrench.

    4.Compare your new oxygen sensor to the old one. If the new one did not come with an electrical connection, but just with the wires stubbed out, you need to do a little work.

    · Cut off the old connector from the bad oxygen sensor, strip the wires and solder the wires to the new oxygen sensor. You can also use butt connectors.

    · Use heat sensitive shrink tape to seal the connections.

    · Follow manufacturer's instructions to know which wires to tie together.

    5.Reverse the steps used in removing the oxygen sensor and install the new part.Add a small amount of anti-seize to the threads of the new sensor. Screw it in place clockwise and snug it down with the socket or open-end wrench. Do not over tighten the sensor as you might strip the threads.

    6.Plug the electrical connections back in.

    7.Turn on the ignition key, but do not start your vehicle. Use the diagnostic scanner/reader to clear the code from the vehicle's computer.

     

    8.Start the car. You should notice an immediate improvement.

     

    NOTE:

     

    If you can't  determine whether the oxygen sensor fit your vehicle or not, please contact us.

     

     

     

     

     

     

    Item Specifics
    Brand :gdcarpartsin
    Manufacturer Part Number :G831838SIN
    Manufacturer Warranty :1 Year
    Fitment Type :Direct Replacement
    Custom Bundle :Yes
    Modified Item :No
    Type :Oxygen Sensor
    Number of Pieces :2
    Wire :4, 4
    Position :Downstream
    Custom Bundle :Yes
    Housing Material :Metal
    Thread Size :18 X 1.5 MM
    Universal Or Specific Fit :Specific
    Automotive Color / Finish :Steel
    Terminal Type :Blade
    Attachment Method :Screw-On
    Output Signal Range (V) :0.2 To 0.8 Volt
    Type :Sensor
    Features :Direct Fit


    1. Orders processed within 24 hours of payment verification.(if you want cancel orders or change address pls contact us within 6 hours after payment,or we are not responsible for shipping a replacement.)
     
    2. We only ship to confirmed PAYPAL addresses. Your PAYPAL address must match your Shipping address.
     
    3. Fast shipping:All our packages use USPS First Class/UPS/Fedex... Package Service
     
    4. If you have not received your shipment within 15 days from payment , please contact!
    1. You have 30 days to contact us and 10 days to return it from the date it was received. If this item is in your possession more than 7 days, it is considered used and we will not issue you a refund or replacement. There are NO EXCEPTIONS!
     
    2. All returned items must be in the original packaging and you must provide us with the shipping tracking number, specific reason for the return, and item custom lable.
     
    3. We will refund your full winning bid amount, upon receipt of the item in its original condition and packaging with all components and accessories included, AFTER both Buyer and Seller cancel the transaction from eBay. OR, you may choose to have a replacement.
     
    4. Return shipping is to be paid by the Buyer
    We strive for 100% customer satisfaction! FEEDBACK IS VERY IMPORTANT TO US.
    We request that you contact us immediately BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concerns. 
    1.We only accept PayPal.
     
    2.Please do not use the PayPal note field to indicate us to ship to other address. The note there will NOT be read. If you want to change the shipping address, please contact us by eBay messages.
     
    3.(if you want cancel orders or change address pls contact us within 6 hours after payment,or we are not responsible for shipping a replacement.)
     
    4.Payment must be received within 10 days as auction ended or order might be delayed.
    1,We stand behind every product we sell.
    2,All of our brand new items come with a 60-Days money-back guarantee.
    3,We define the item as defective only if it doesn't function as described.
    4,It is the buyer's responsibility to understand the item description before bidding.
    5,We will replace the defective items, provided that they are in stock within the warranty period posted with the listing and the buyer return the  original item and pay for the S&H cost for the replacement.
     6,We  will refund the purchase price if the replacement is not available or buyer  prefers a refund and send the original item back at his/her own cost.
    7,Shipping & handling cost are not refundable.
    8,Man-made damage by  abuse or wrong operation is not covered by this warranty.
    9,No  product liability insurance is assumed.

    All rights reserved.