6V 12V 3A(Suitable for 6V/12V Lead acid/colloid battery)
Regulator
Material: Plastic
Size: 53.4*68*6*22mm
System Voltage: 6V, 12V
Output Current: 3A
Power Range: ≤60W(6V), ≤120W(12V)
Overload, Short Circuit Protection: Yes
No-load loss: ≤5mA
Charge Loop Drop: ≤0.2V
Disharge Loop Drop: ≤0.1V
Protection Degree: IP30
Working Temperature: -30°~55°
Package Included:
1* Solar Charge Controller
1*Manual
6V 12V 10A(Suitable for 6V/12V Lead acid/colloid battery)
Regulator PWM
Specification:
Brand new
Material: Plastic
System Voltage: 6V, 12V
Output Current: 10A
Power Range: ≤60W(6V), ≤120W(12V)
Overload, Short Circuit Protection: Yes
No-load loss: ≤5mA
Charge Loop Drop: ≤0.2V
Disharge Loop Drop: ≤0.1V
Protection Degree: IP30
Working Temperature: -40℃~55℃
Package Included:
1* Auto Solar Charge Controller
1*Manual
12V 10A(Suitable for 12V Lead acid/colloid battery)
Regulato
Description:
Warnings for usage:
- The batteries has stored much energy,please keep the batteries from the short circuit under any circumstances,we strongly recommend connecting the batteries with the fuse.
- Please avoid the short circuit wire and the terminal,for the wire and the terminal may generate voltage two times higher than the rated voltage of the controller.please use the insulated tools while operating the controller.
- Because of the equipment work may have a fever, please keep ventilation.The device pay attention to water,moisture,in order to avoid damage to the equipment.
Suitable range:
- The controller is only applicable to solar power, rated voltage of 12v systems, battery of gel batteries, liquid openings or sealed lead-acid batteries.
- note: specifically how much battery charge, see the product model, product can not be adapted to the various systems.
Characteristics:
- Equipped with the mcu, artificially controlled.
- Equipped with device to avoid the overcharge, over release, electronic short circuit, over loading, battery inversely connecting, solar battery inversely connecting.
- Use the battery discharge rate characteristics to correct discharge control。
- The series connection pwm circuit is implemented to form the major charging
- Make the voltage loss half of or lower than the diode charging circuit, and the charging efficiency 3%-6% higher than the non-pwm.
- The led shows the batteries current situation to make the customer get the information of the batteries.
- Three operating modes can be selected: normally open mode, the pure light control mode and light control plus timing mode.
Package Included:
1*Solar Charge Controller
1*Manual
11.1V 10A(Suitable for 18650/Polymer battery)
Specification:
- Material: Plastic
- System Voltage: 11.1V
- Output Current: 10A
- Power Range: ≤111W
- Overload, Short Circuit Protection: Yes
- No-load loss: ≤6mA
- Charge Loop Drop: ≤0.2V
- Disharge Loop Drop: ≤0.1V
- Protection Degree: IP30
- Working Temperature: -40℃~55℃
Package Included:
1*Solar Charge Controller
1*Manual
11.1V 3A(Suitable for 18650/Polymer battery)
Characteristics of the function:
Working for Li-ion battery’s charging control
Voltage: 11.1V
Current: 3A
Working temperature: -30 ℃-55℃
Equipped with the MCU, artificially controlled.
Equipped with device to avoid the overcharge, over release, electronic short circuit, over loading, battery inversely connecting, solar battery inversely connecting.
Use the battery discharge rate characteristics to correct discharge control.
The series connection PWM circuit is implemented to form the major charging circuit, make the voltage loss 50% or lower than the diode charging circuit, and the charging efficiency 3%-6% higher than the non-PWM.
The LED displayer shows the batteries current situation to make the customer get the information of the batteries.
Three operatiing modes can be selected: normally open mode, the pure light control mode and light control plus timing mode.
Package Included:
1*Solar Charge Controller
1*Manual
Above Install and Method of Using:
Firstly, determine the controller output mode , the device factory default setting is normally open mode .if you need to set for the pure light control mode or light control plus timing mode, you need to open the enclosure through set dip switch, changing the discharge mode
When the key set "on" is 1, the key set "off" is 0, normally open, pure light control
Connecting the battery first. if correctly connected, battery indicator will light
Connecting the wire of the solar panel second. if the connection is correct, the indicator light of “charge”will be on or flash 10 seconds later after laying outside under the sun. otherwise, please check the connection
Making sure the solar energy panel is laid outdoors under the sunshine
Connecting the load at the end. if inversely connected, the led lamp may be damaged
Please pay attention to the anode and the cathode to avoid the inverse connection.