Please note: Your order may not be shipped for 7-30+ days after it's paid for. That is our order process time, ALSO please factor in shipping transit time of 7-15 days. This is for in stock items; some items are occasionally on back-order and could be delayed longer than 30 days. International orders on average take twice as long to be delivered so please understand the extra shipping time if you are out of the USA. Please before leaving Negative / Neutral feedback send us a message with the issue. We have been in business for over 18 years and we will be sure to resolve it 100% . We have been trying very hard to obtain a 5 star Detailed Seller Rating. (DSR), please know that we strive for the ultimate 5-star performance and hope you are happy with our transaction.
As the leader in Custom Corvette products especially the Tail Light and smoked marker lights we are again the first to create this kit. Others will follow but none can be GScreations! We also proudly make this kit in the USA. Ask the other guys that!
What you get: This is a 4 piece kit. This kit is for the large "L" shaped parking light covers only in a poly-carbonate lexan transparent smoked blackout look. (You can use the drop down to add the reflector covers if desired).
The available "Add reflector covers" above are as follows below since the visible text seems to have a charter limit in the drop down..
-No thank you, just 4 pcs kit wanted
-Yes, please add 4 inner reflector covers
-Yes, please add 4 inner & 2 side reflector covers
What they fit: 2020, 2021, 2022, 2023, 2024+ C8 Corvette Stingrays, Z06 E-Ray's in all trim levels with factory C8 Corvette tail lights.
Material: Our covers are molded from 1/8'' thick Poly-carbonate lexan. (Poly-carbonate aka lexan, is a tough and durable plastic material which is virtually unbreakable with 250 times the impact strength of glass and 30 times that of acrylic.) What does this mean to you...they will not break when installing, removing or heck even if you drop them unlike their predecessor C7 blackouts which were made from acrylic. The smoked color is built into the lexan so no worries about paint fade, peeling or chipping over the years.
How they install: Amazingly simple!! Since ours is only 4 pieces total it will take you under 2 minutes. Each cover will come with pre-installed clear 3m tape. You simply clean your lights with the supplied alcohol, and let dry. Once dry remove the red tape backing and press on firmly for a few seconds. That's it! You do not need to remove your rear bumper to install these covers.
These covers by design do not create an air or water tight seal. They were designed with water channels to allow water to flow through them. This simply means hassle free maintenance, if you see any dirt or grim between the factory light and the new cover simply spray water along the top or side edge to wash it away.
It is 100% completely normal to see a whitish fog after a wash or driving in rain. This is just condensation and will completely go away when dry. Dry time will depend on many factors with relative humidity playing a large role in that time. The photo below shows this normal condensation.
When you use your Parking lights they are still highly visible. We have been using this level of smoke on all of our lights since the C5 Corvette!
If your vehicle was ever waxed or ceramic coated most likely so was the area you are installing this product on even if it's a light or reflector. You MUST remove any wax or ceramic coating before you install this product or the 3m tape used will not stick. Alcohol alone will not do this, please consult with your detailer to find the best way to remove. You should test the area before install by putting any tape on the light and if there is good adhesion you should be okay. If the tape you used for the test does not stick or comes off very easy so will our covers.
Make GScreations your #1 place for all your C5/C6/C7/C8 Corvette parts, aftermarket accessories & apparel!! |
Check out our other items!!
All installation and use of the products purchased from GSCreations, LLC are done at the owners own risk. GSCreations, LLC will not be held responsible for any damage or injury caused by the installation or use of the products purchased here. By using and / or purchasing any product from this Ebay seller (GSCREATIONS01), you agree to the terms above.