• • • 1 x 4 Axis 200KHz NVEM Ethernet USB Mach3 Motion Control Card 
    • 1 x Network Cable
    • 1 x English Manual Will send by Email
    • 
      
    • 
      

    •  

4 Axis Ethernet MACH3 Motion Control Card NVEM

• • 
    

    4 Axis Ethernet MACH3 Motion Control Card NVEM

    1. Performance parameter

    
    

    Features:

    1) Can control up to 3/4/5/6 stepper motor at the same time.

    2) Support Motor: Servo motor, Stepper motor.

    3) With 12 channel programmable input port.

    4) With 10 channel programmable output port.

    5) 1 channel standard MPG interface

    6) PWM output control

    7) Ethernet interface, support MACH3 software

    8) DC electrical isolation

    9) Optocoupler isolation

    10) Up to 200KHz stepper motor control pulse output

    Specification:

    1) Support Ethernet;

    2) 12 ports photoelectric isolated input interface for ordinary digital data;

    3) 10 ports photoelectric isolated output interface for ordinary digital data;

    4) 1 port 0-10V spindle speed analog output interface(can change to PWM output);

    5) Can support 3-6 axis stepper systems,200KHz pulse output for every axis;

    6) ARM motion control chip;

    7) Main device is 12V-32VDC power supply input,current should higher than 0.5A;

    8) Compatible with MPG input,support the digital display MPG from our company.

    2. Product connection define and method
    

    
    

    

    Product wiring section and interface summary

    As
    the figure showed,the connection of the controller includes power
    supply interface,Ethernet connection
    interface,MPGinterface,Stepper/Servo control output interface,spindle
    control output interface, Estop and limited switch and tool setting
    input interface and so on. Now we descript them in details as below.

    
    

    2.1) Stepper motor control interface

    No.1
    terminal block is 6 axis stepper driver control output interface, from
    left to right,there are X,Y,Z,A,,B,C 6 axis output, it’s common
    anode,the cable connection for each axis is COM+/CP-/DIR-, COM is
    common+ ,CP is Pulse-, DIR is direction-.Connection showed as Figure
    2-3.COM+ connect with the SP+ and DIR+.

    	Pin mark	Axis	Definition
    	COM+	Commom+	common anode +5V
    	CPX-	X axis	Pulse output- for X axis
    	DIX-	X axis	Directrion output- for X axis
    	CPY-	Y axis	Pulse output- for Y axis
    	DIY-	Y axis	Directrion output- for Y axis
    	CPZ-	Z axis	Pulse output- for Z axis
    	DIZ-	Z axis	Directrion output- for Z axis
    	CPA-	A axis	Pulse output- for A axis
    	DIA-	A axis	Directrion output- for A axis
    	CPB-	B axis	Pulse output- for B axis
    	DIB-	B axis	Directrion output- for B axis
    	CPC-	C axis	Pulse output- for C axis
    	DIC-	C axis	Directrion output- for C axis

    

    
    

    
    

    2.2) Spindle control output

    
    

    We define the interface from left are: GND1(Output GND),VSO(0-10V adjustable
    speed output),INDEX(spindle speed feedback input),OUT1(common output
    port 1),OUT2(common output port 2),.

    Take Nowforeuer inverter as the example. Spindle control output and the
    inverter connection showed as Figure 2-4.If ACM and DCM are closed,only
    need to connect one port.

    If need the Mach 3 to show the real in time spindle speed,just fix one
    hall device,every revolution send one pulse between INDEX and GND1,pulse
    voltage is 5V-10V.