eBay

Important Note:

Make sure the AIO's slightly bigger size can fit your own quad! The size of this AIO is 36.5(L)36.5(W)7.0(H)mm.
We suggest you use this AIO on your 3.5" to 5" cinewhoops/long-range or lightweight quads.For quads below 3.5",you should carefully check if your quad has enough room for this AIO.

Specifications

Overview
Product Name	SpeedyBee F745 35A BLS AIO
Power Input	3S - 6S Lipo
Mounting	25.5 x 25.5mm, 3mm hole diameter
Dimension	36.5mm(L) x 36.5mm(W) x 7mm(H), recommended for quads at 3.5" or above
Weight	10.1g
FC
MCU	STM32F745
IMU(Gyro)	MPU6000
USB Connection	Need to solder a USB TYPE-C module to D+,D-,GND pads.
Barometer	BMP280
OSD	Supported
BLE Bluetooth	Supported. Used for parameter configuration
Flash FC Firmware Wirelessly	Supported
Download/Analyze Blackbox	Supported
DJI Air Unit 6-pin Connector	Built-in.
Flash(for BlackBox)	8MB
Current Sensor	Supported. Scale=256
BetaFlight Camera Control Pad	Yes(CC pad)
5V Output	4 groups of 5V output. The total current load is 2.5A.
9V Output	None
3.3V Output	Supported. Up to 500mA current load.
ESC Signal Pads	M1 - M4
UART	Full UART * 4(UART1, UART2, UART3,UART4)
ESC Telemetry UART	None
I2C	Supported.
LED Pad	Used for WS2812 LED
Buzzer	BZ+ and BZ- pad used for 5V Buzzer
BOOT Button	Used to enter DFU mode
RSSI Input	Not supported
SmartPort	Use any TX pad of UART for the SmartPort feature.
Supported Flight Controller	BetaFlight(Default)
Firmware Target Name	SPEEDYBEE F745AIO
ESC
Power Input	3-6S LiPo
Continuous Current	35A * 4
Burst Current	45A(5S)
ESC Protocol	DSHOT300/600
Power Output	VBAT
Current Sensor	Supported(Sacle=256)
Firmware	BLHeli_S JH40

Important Note:

Make sure the AIO's slightly bigger size can fit your own quad! The size of this AIO is 36.5(L)*36.5(W)*7.0(H)mm.
We suggest you use this AIO on your 3.5" to 5" cinewhoops/long-range or lightweight quads.For quads below 3.5",
you should carefully check if your quad has enough room for this AIO.

Important Note:

Welcome to My Store

Make sure the AIO's slightly bigger size can fit your own quad! The size of this AIO is 36.5(L)*36.5(W)*7.0(H)mm.We suggest you use this AIO on your 3.5" to 5" cinewhoops/long-range or lightweight quads.For quads below 3.5",you should carefully check if your quad has enough room for this AIO.

Overview

Product Name

SpeedyBee F745 35A BLS AIO

Power Input

3S - 6S Lipo

Mounting

25.5 x 25.5mm, 3mm hole diameter

Dimension

36.5mm(L) x 36.5mm(W) x 7mm(H), recommended for quads at 3.5" or above

Weight

10.1g

FC

MCU

STM32F745

IMU(Gyro)

MPU6000

USB Connection

Need to solder a USB TYPE-C module to D+,D-,GND pads.

Barometer

BMP280

OSD

Supported

BLE Bluetooth

Supported. Used for parameter configuration

Flash FC Firmware Wirelessly

Supported

Download/Analyze Blackbox

Supported

DJI Air Unit 6-pin Connector

Built-in.

Flash(for BlackBox)

8MB

Current Sensor

Supported. Scale=256

BetaFlight Camera Control Pad

Yes(CC pad)

5V Output

4 groups of 5V output. The total current load is 2.5A.

9V Output

None

3.3V Output

Supported. Up to 500mA current load.

ESC Signal Pads

M1 - M4

UART

Full UART * 4(UART1, UART2, UART3,UART4)

ESC Telemetry UART

None

I2C

Supported.

LED Pad

Used for WS2812 LED

Buzzer

BZ+ and BZ- pad used for 5V Buzzer

BOOT Button

Used to enter DFU mode

RSSI Input

Not supported

SmartPort

Use any TX pad of UART for the SmartPort feature.

Supported Flight Controller

BetaFlight(Default)

Firmware Target Name

SPEEDYBEE F745AIO

ESC

Power Input

3-6S LiPo

Continuous Current

35A * 4

Burst Current

45A(5S)

ESC Protocol

DSHOT300/600

Power Output

VBAT

Current Sensor

Supported(Sacle=256)

Firmware

BLHeli_S JH40

Make sure the AIO's slightly bigger size can fit your own quad! The size of this AIO is 36.5(L)36.5(W)7.0(H)mm.
We suggest you use this AIO on your 3.5" to 5" cinewhoops/long-range or lightweight quads.For quads below 3.5",you should carefully check if your quad has enough room for this AIO.