Store Categories
Product View
Details
The charging process is divided into the following three processes: trickle mode, constant current mode and constant voltage mode. When the battery voltage is lower than 3V, the charging module is in trickle mode, and the charging current is 300mA; when the battery voltage is greater than 3V, the charging module enters into constant current mode, and the charging current is charged at full speed according to the set target current, and the power can be about 21W; when the battery voltage rises to the charging target voltage (for example, 4.2V), the charging module enters into constant voltage mode, and the current gradually decreases at this time, while the battery When the charging current decreases to the charging cut-off current, charging ends. If the battery voltage decreases to 0.1V lower than the target voltage after full charging, charging will be restarted automatically. (Note: voltage over 4.2V is normal, will not charge bad battery, voltage of 4.2V when the light is still flashing means not yet full, full charge is not only to see the charging voltage)
Specification
Switching charging: current up to 5A, efficiency up to 95%; support 4.2/4.35/4.4/4.5V battery type; support JEITA specification; support temperature ring control
Synchronous boost: output power up to 22.5W, efficiency up to 95%; automatic load detection/light load detection; support for wireless charging mode; support for low current mode
Output fast charging protocol: support PPS/PD3.0/PD2.0; support QC4+/QC4/QC3.0/QC2.0; support AFC; support FCP; support SCP; support PE2.0/PE1.1; support SFCP; support VOOC
Input fast charging protocol: support PD3.0/PD2.0; support AFC; support FCP; support SCP; support PE1.1
Type-C interface: built-in USB Type-C interface logic; support Try.
BC1.2 module: support BC1.2 DCP mode; support Apple/Samsung mode
Protection mechanism: input over-voltage protection; output over-current/short-circuit protection; charging timeout/over-voltage protection; temperature protection
Switching charging: current up to 5A, efficiency up to 95%; support 4.2/4.35/4.4/4.5V battery type; support JEITA specification; support temperature ring control
Synchronous boost: output power up to 22.5W, efficiency up to 95%; automatic load detection/light load detection; support for wireless charging mode; support for low current mode
Output fast charging protocol: support PPS/PD3.0/PD2.0; support QC4+/QC4/QC3.0/QC2.0; support AFC; support FCP; support SCP; support PE2.0/PE1.1; support SFCP; support VOOC
Input fast charging protocol: support PD3.0/PD2.0; support AFC; support FCP; support SCP; support PE1.1
Type-C interface: built-in USB Type-C interface logic; support Try.
BC1.2 module: support BC1.2 DCP mode; support Apple/Samsung mode
Protection mechanism: input over-voltage protection; output over-current/short-circuit protection; charging timeout/over-voltage protection; temperature protection
Note
1: The motherboard external battery line needs to be able to pass 10A current, at least 1 square copper wire, the ordinary line to use 1.5 square. Not necessary too thick, but not too thin, too thin will be a safety hazard. (Because the battery side of the current is very large)
2: The motherboard comes with a protection chip, the battery can no longer add a protection board, if there is please remove the protection board, directly our motherboard connected to the battery cell. (Because the self-contained generally can not be over high current, the output power a large protection)
3: the use of alligator clips to test the use of the motherboard partners please do not charge the phone, do not ask why, in short, can not be used in this way. Need to charge the phone must be welded must be welded.
4: The battery with 4.2V 18650 / polymer / ternary lithium batteries, large single can, multiple 18650 parallel can also be used, can not use lithium iron batteries, disposable dry cell, NiMH, lead-acid batteries, nickel-cadmium batteries, etc.. Batteries can not be connected in series access. The first time the power will be inaccurate power display, etc., please discharge and then fill it up, the first charge can continue to charge for more than 5 hours when the 4 lights are fully lit, will not be charged bad battery, no need to worry.
1: The motherboard external battery line needs to be able to pass 10A current, at least 1 square copper wire, the ordinary line to use 1.5 square. Not necessary too thick, but not too thin, too thin will be a safety hazard. (Because the battery side of the current is very large)
2: The motherboard comes with a protection chip, the battery can no longer add a protection board, if there is please remove the protection board, directly our motherboard connected to the battery cell. (Because the self-contained generally can not be over high current, the output power a large protection)
3: the use of alligator clips to test the use of the motherboard partners please do not charge the phone, do not ask why, in short, can not be used in this way. Need to charge the phone must be welded must be welded.
4: The battery with 4.2V 18650 / polymer / ternary lithium batteries, large single can, multiple 18650 parallel can also be used, can not use lithium iron batteries, disposable dry cell, NiMH, lead-acid batteries, nickel-cadmium batteries, etc.. Batteries can not be connected in series access. The first time the power will be inaccurate power display, etc., please discharge and then fill it up, the first charge can continue to charge for more than 5 hours when the 4 lights are fully lit, will not be charged bad battery, no need to worry.
List
1 x Mobile power module circuit board
1 x Mobile power module circuit board
Copyright©2018 datacaciques
Store Categories
Product View
Details
The charging process is divided into the following three processes: trickle mode, constant current mode and constant voltage mode. When the battery voltage is lower than 3V, the charging module is in trickle mode, and the charging current is 300mA; when the battery voltage is greater than 3V, the charging module enters into constant current mode, and the charging current is charged at full speed according to the set target current, and the power can be about 21W; when the battery voltage rises to the charging target voltage (for example, 4.2V), the charging module enters into constant voltage mode, and the current gradually decreases at this time, while the battery When the charging current decreases to the charging cut-off current, charging ends. If the battery voltage decreases to 0.1V lower than the target voltage after full charging, charging will be restarted automatically. (Note: voltage over 4.2V is normal, will not charge bad battery, voltage of 4.2V when the light is still flashing means not yet full, full charge is not only to see the charging voltage)
Specification
Switching charging: current up to 5A, efficiency up to 95%; support 4.2/4.35/4.4/4.5V battery type; support JEITA specification; support temperature ring control
Synchronous boost: output power up to 22.5W, efficiency up to 95%; automatic load detection/light load detection; support for wireless charging mode; support for low current mode
Output fast charging protocol: support PPS/PD3.0/PD2.0; support QC4+/QC4/QC3.0/QC2.0; support AFC; support FCP; support SCP; support PE2.0/PE1.1; support SFCP; support VOOC
Input fast charging protocol: support PD3.0/PD2.0; support AFC; support FCP; support SCP; support PE1.1
Type-C interface: built-in USB Type-C interface logic; support Try.
BC1.2 module: support BC1.2 DCP mode; support Apple/Samsung mode
Protection mechanism: input over-voltage protection; output over-current/short-circuit protection; charging timeout/over-voltage protection; temperature protection
Switching charging: current up to 5A, efficiency up to 95%; support 4.2/4.35/4.4/4.5V battery type; support JEITA specification; support temperature ring control
Synchronous boost: output power up to 22.5W, efficiency up to 95%; automatic load detection/light load detection; support for wireless charging mode; support for low current mode
Output fast charging protocol: support PPS/PD3.0/PD2.0; support QC4+/QC4/QC3.0/QC2.0; support AFC; support FCP; support SCP; support PE2.0/PE1.1; support SFCP; support VOOC
Input fast charging protocol: support PD3.0/PD2.0; support AFC; support FCP; support SCP; support PE1.1
Type-C interface: built-in USB Type-C interface logic; support Try.
BC1.2 module: support BC1.2 DCP mode; support Apple/Samsung mode
Protection mechanism: input over-voltage protection; output over-current/short-circuit protection; charging timeout/over-voltage protection; temperature protection
Note
1: The motherboard external battery line needs to be able to pass 10A current, at least 1 square copper wire, the ordinary line to use 1.5 square. Not necessary too thick, but not too thin, too thin will be a safety hazard. (Because the battery side of the current is very large)
2: The motherboard comes with a protection chip, the battery can no longer add a protection board, if there is please remove the protection board, directly our motherboard connected to the battery cell. (Because the self-contained generally can not be over high current, the output power a large protection)
3: the use of alligator clips to test the use of the motherboard partners please do not charge the phone, do not ask why, in short, can not be used in this way. Need to charge the phone must be welded must be welded.
4: The battery with 4.2V 18650 / polymer / ternary lithium batteries, large single can, multiple 18650 parallel can also be used, can not use lithium iron batteries, disposable dry cell, NiMH, lead-acid batteries, nickel-cadmium batteries, etc.. Batteries can not be connected in series access. The first time the power will be inaccurate power display, etc., please discharge and then fill it up, the first charge can continue to charge for more than 5 hours when the 4 lights are fully lit, will not be charged bad battery, no need to worry.
1: The motherboard external battery line needs to be able to pass 10A current, at least 1 square copper wire, the ordinary line to use 1.5 square. Not necessary too thick, but not too thin, too thin will be a safety hazard. (Because the battery side of the current is very large)
2: The motherboard comes with a protection chip, the battery can no longer add a protection board, if there is please remove the protection board, directly our motherboard connected to the battery cell. (Because the self-contained generally can not be over high current, the output power a large protection)
3: the use of alligator clips to test the use of the motherboard partners please do not charge the phone, do not ask why, in short, can not be used in this way. Need to charge the phone must be welded must be welded.
4: The battery with 4.2V 18650 / polymer / ternary lithium batteries, large single can, multiple 18650 parallel can also be used, can not use lithium iron batteries, disposable dry cell, NiMH, lead-acid batteries, nickel-cadmium batteries, etc.. Batteries can not be connected in series access. The first time the power will be inaccurate power display, etc., please discharge and then fill it up, the first charge can continue to charge for more than 5 hours when the 4 lights are fully lit, will not be charged bad battery, no need to worry.
List
1 x Mobile power module circuit board
1 x Mobile power module circuit board
We will arrange shipping for you within 24 Hours after payment cleared except the holidays.
-We ship items to Worldwide. Thank you!
-we will ship out the order in 1-2 business days after payment cleared .Since it is international shipping ,delivery time is about 15--28 business days to arrive to most countries.
We accept PayPal payment ONLY, and must be received within 5 days from the date of purchase.
2. It is easy and safe for you to pay by credit cards, debit cards, bank transfers and PayPal account balances.
3.Buyers are responsible for import duties,custom fees and taxes, if any, please check your country.
1.We believe our items are so outstanding. We are convinced you will be happy with your Purchase.
2. If you do not satisfy with our items. Please simply return to us within 30 Days in original condition. Just pay for the returned postage. Then we can issue full refund or resend the item to you after the returned item arrived at our warehouse.
3. Please include your eBay ID and item number with any email requests.