Wavlink Wireless 2.4GHz Long Range 300Mbps Outdoor Access Point/Repeater CPE Kit for PTP and PTMP Transmission | Point to Point WiFi Bridge
- 1.5km Wireless Data Transmission: Specially designed for outdoor uses, ideal for long distance wireless data transmission over 1.5km(only for paired PtP or PtMP transmission), tested in the barrier-free field. Built-in 11dBi directional antennas can significantly improve the transmission and reception performance of wireless signal.
- Excellent WiFi Access "Helper": It supports up to 64 devices and provides 300Mbps high speed with 100M Ethernet port and 2*2 MIMO antenna. Point to Point/Multi-Point connection (1-4) can be used for elevator monitor/surveillance networks. Simple settings can achieve wireless optimization, and improve the quality and effectiveness of link transmission.
- Built for Outdoor Wi-Fi Coverage: IP65-rated waterproof housing that ensures continued operation on harsh outdoor environments or in climates of extreme cold, heat or continuous moisture. Lightning protection and weatheproof design ensure stable connection in harsh outdoor conditions.
- Flexible Deployment: 24V passive PoE adapter supports up to 80 meter (262 feet) deployment, for easier installation and lower cost. And it can be installed in areas where power outlets are not readily available, eliminating the mess of altering existing network infrastructure.
- Multi-Working Modes Accessible: Supports AP/Router/Repeater Mode, which can meet your network requirements in different environment. 200 meters wireless data transmission range specifically determined by the environment and the antenna gain and power of the client.
|
|
|
|---|---|---|
Multiple LED Indicators6 status LED indicators help you see the power/ internet status of device. Since the green lights might be not so obvious in the open air, you can try to cover the device with your hand to check. | Flexible PoE DeploymentSupport 24V PoE power supply, easy installation and deployment. Make sure the Ethernet cable connected to this repeater be less than 80 meters, and the ethernet cable connected to the uplink devices be less than 100 meters. | Wide Range Transmission1.5km wireless data transmission range for point to point/multi-point use(the result is from testing two products use together---one as sender and one as receiver), suitable for surveillance networks. |
Enjoy Outdoor WiFi
- IP65-rated weatherproof housing
- Withstanding broad ranges of humidity and temperature(-30°C~70°C) (-22°F~158°F)
- Build in lightning arrester (15KV ESD), 4KV lightning protection
3-IN-1 Mode
- Repeater Mode is for extending wifi coverage of an existing wireless network;
- Router Mode is for creating an instant private wireless network and enable multiple devices to share it;
- AP Mode is for covering a wired network to a wireless network.
Installation Height: Keep the height of the flat antenna 2-3 meters above the ground without obstruction, and 1-2 meters horizontal drop from the network terminal (mobile phone, surveillance camera).
Installation Direction: The signal facing the front of the panel antenna is much stronger, please pay attention to whether the front and back of the antenna panel are facing correctly when installing.
FAQ
Q1. Why doesn't the login page appear after entering wifi.wavlink.com?
-If your computer is wirelessly connected, please verify that you have connected to the device's SSID. If your computer is connected via an Ethernet cable, please verify that the connection is stable.
-Make sure your computer is set to obtain an IP address automatically.
-Use the IP address to log in to the page. The default IP is 192.168.10.1. If the device is connected to the host Wi-Fi, please go to the router 's DHCP client list to obtain the device' s current IP address.
-Please reset the device and try again. If the problem still exists, please feel free to let us know.
Q2. How do I restore the device to its factory default settings?
-While the device is powered on, press and hold the Reset button until all the LEDs turn on momentarily.
Q3. What should I do if the LED does not change to solid after completing ?
-You may have entered the incorrect Wi-Fi password of your host Wi-Fi during the configuration. Please log into the device' s web-based interface to check the password and try again.
-Reset the device and go through the configuration again.
Q4. I have enabled a wireless MAC filter, wireless access control, or access control list (ACL) on my router. What should I do before configuring and using the device ?
-If you have enabled those functions of your router, you may need to disable them first. And then follow OPTION ONE or OPTION TWO to complete the configuration. .
For more details, please refer to WAVLINK Website.
