|
|
|
|
|
|
|
|
|
|
|
|
|
NOTE:
Before installing the new assembly, inspect the intake-manifold-to-throttle-body gasket for damage. If it is damaged, it must be replaced.
If it is in good condition, it can be reused.
WARNING:
DO NOT place fingers in or around the throttle body plate. If the throttle body is energized, the throttle plate could move causing personal injury. Always disconnect the negative battery cable prior to servicing the throttle body.
CAUTION:
DO NOT move the throttle plate while power is connected to the throttle body. This may cause fault codes to set.
Q: Is there anything that has to be done after installing the replacement throttle body?
A: A relearn calibration procedure is necessary after installation of replacement throttle body
Q: What is throttle body relearn?
A: Idle Relearn (aka throttle body relearn) is the procedure that is required to obtain the correct idle speed after replacing electronic throttle body, disconnecting a battery cable, clearing a check engine light, etc.
Relearn A MECHANICALLY CONTROLLED THROTTLE BODY
1. Remove terminals from the battery for 15 minutes.
2. Start the engine. Let it idle for 10 minutes. Remember not to switch on any additional consumers.
3. Stop the engine for about 10 seconds. Start it again.
4. Wait until the power unit warms up to the operating temperature. After that, you can start using the vehicle.
Take notice: you might need to drive 150–200 km until the idling stabilises.
Relearn AN ELECTRONICALLY CONTROLLED THROTTLE BODY
The readjustment process might vary in different vehicles. Therefore, before you start the procedure, consult the vehicle manual for the exact step sequence.
The general algorithm is as follows:
1. Study procedure and try to remember it. You’ll have to act quickly so you won’t have time to check the details.
2. Start the engine. Warm it up to the working temperature.Stop it for 10 seconds.
3. Switch on the ignition for 3 seconds.
4. Press the accelerator pedal quickly for 5 times. One depression should take one second.
5. Press the gas pedal to the floor for 7 seconds. Keep it depressed until the “Check Engine” light burns steady and hold it for 3 more seconds.
6. Press the gas pedal to the floor for 7 seconds. Keep it depressed until the “Check Engine” light burns steady and hold it for 3 more seconds.
7. Release the gas pedal and start the engine.
Q: HOW TO PREVENT THE THROTTLE BODY FROM GETTING DIRTY?
A: 1. Use only high-quality fuel. Otherwise, impurities and contaminants will get inside the engine causing the rapid formation of carbon deposits on the throttle body. For the same reason, you shouldn’t neglect the fuel filter replacement. It is recommended to flush the fuel tank from time to time.
2. Replace the air filter on time. Always make sure that the intake system is air-tight. This simple check prevents unfiltered air from being sucked into the intake system in places where its components are not connected tightly.
3. Always make sure that the crankcase ventilation system is fault-free. Its malfunctions cause a fast formation of oily deposits on elements of the throttle body.
Item Specifics | |
---|---|
Brand | Autodealsparts |
Manufacturer Part Number | AUT104935-1TA01 |
Housing Length (in) | 5-1/2 |
Bore Diameter | 3.15 in (70mm) |
Housing Width (in) | 5-1/16 |
Main Port Inside Diameter(in) | 3 |
Air Intake Port Maximum Diameter (in) | 3-3/16 |
Throttle Plate Diameter (in) | 2-3/4 |
Fitment Type | Direct Replacement |
Manufacturer Warranty | 1 Year |
Throttle Body Actuation Type | Electrical |
Items Included | Throttle Position Sensor |
Terminal QTY | 6 |
Gaskets Included | No |
Material | Aluminum |
Interchange Part Number | 67-0001 |
OE/OEM Part Number | 977-563 |
Superseded Part Number | 977-563 |
Weight | 4 LB |
Placement on Vehicle | Front |
Mount Hole Quantity | 4 |
Connector Quantity | 1 |
Fuel System Type | FI |
Packaging Type | Box |
Modified Item | No |
Custom Bundle | No |
Non-Domestic Product | Yes |
Mounting Hardware Included | No |
Type | Throttle Body |
OE | 977-563 |
Features | Electronic |
Connector Type | Blade |
Fuel Type | Gasoline |
Performance Part | Yes |
Color | Silver |
Inlet Type | Non-Flanged |
Universal Fitment | No |
Vintage Part | No |
Outlet Type | Non-Flanged |
We only accept PayPal.
1. We only ship to confirmed paypal addresses, your paypal address must match your shipping address.
2. All domestic orders will be shipped via USPS, UPS or Fedex from our US warehouse and usually arrives to your door in about 2-7 business days.
3. If you have not received your shipment within 15 days from payment , please contact us. We will track the shipment and get back to you as soon as possible with a reply.
4. Local pick up is not available.
All of our brand new items come with a 30-days money-back guarantee.
If you have any question, please contact us.
Cancer and Reproductive Harm - www.P65Warnings.ca.gov.
Autodealsparts
Shop Category Picture Picture Picture |
Fits Nissan For Fits For Murano 3.5L 2007 04-06 2003 Throttle Body 161198J103
NOTE: Before installing the new assembly, inspect the intake-manifold-to-throttle-body gasket for damage. If it is damaged, it must be replaced. If it is in good condition, it can be reused.
WARNING: DO NOT place fingers in or around the throttle body plate. If the throttle body is energized, the throttle plate could move causing personal injury. Always disconnect the negative battery cable prior to servicing the throttle body.
CAUTION: DO NOT move the throttle plate while power is connected to the throttle body. This may cause fault codes to set.
Q: Is there anything that has to be done after installing the replacement throttle body? A: A relearn calibration procedure is necessary after installation of replacement throttle body
Q: What is throttle body relearn? A: Idle Relearn (aka throttle body relearn) is the procedure that is required to obtain the correct idle speed after replacing electronic throttle body, disconnecting a battery cable, clearing a check engine light, etc.
Relearn A MECHANICALLY CONTROLLED THROTTLE BODY 1. Remove terminals from the battery for 15 minutes. 2. Start the engine. Let it idle for 10 minutes. Remember not to switch on any additional consumers. 3. Stop the engine for about 10 seconds. Start it again. 4. Wait until the power unit warms up to the operating temperature. After that, you can start using the vehicle. Take notice: you might need to drive 150–200 km until the idling stabilises.
Relearn AN ELECTRONICALLY CONTROLLED THROTTLE BODY The readjustment process might vary in different vehicles. Therefore, before you start the procedure, consult the vehicle manual for the exact step sequence.
The general algorithm is as follows: 1. Study procedure and try to remember it. You’ll have to act quickly so you won’t have time to check the details. 2. Start the engine. Warm it up to the working temperature.Stop it for 10 seconds. 3. Switch on the ignition for 3 seconds. 4. Press the accelerator pedal quickly for 5 times. One depression should take one second. 5. Press the gas pedal to the floor for 7 seconds. Keep it depressed until the “Check Engine” light burns steady and hold it for 3 more seconds. 6. Press the gas pedal to the floor for 7 seconds. Keep it depressed until the “Check Engine” light burns steady and hold it for 3 more seconds. 7. Release the gas pedal and start the engine.
Q: HOW TO PREVENT THE THROTTLE BODY FROM GETTING DIRTY? A: 1. Use only high-quality fuel. Otherwise, impurities and contaminants will get inside the engine causing the rapid formation of carbon deposits on the throttle body. For the same reason, you shouldn’t neglect the fuel filter replacement. It is recommended to flush the fuel tank from time to time. 2. Replace the air filter on time. Always make sure that the intake system is air-tight. This simple check prevents unfiltered air from being sucked into the intake system in places where its components are not connected tightly. 3. Always make sure that the crankcase ventilation system is fault-free. Its malfunctions cause a fast formation of oily deposits on elements of the throttle body.
Payment
We only accept PayPal. Shipping
1. We only ship to confirmed paypal addresses, your paypal address must match your shipping address.
Returns
All of our brand new items come with a 30-days money-back guarantee. Contact Us
If you have any question, please contact us. Warning
Cancer and Reproductive Harm - www.P65Warnings.ca.gov. All rights reserved. |