ATTINY85-20SU SOP-8
Features:
Tiny85-20SU ATTINY85-20SU ATMEL SOP-8 CHIP IC
Package included：
Tiny85-20SU ATTINY85-20SU ATMEL SOP-8 CHIP IC
ATTINY85-20PU DIP-8
ATTINY85-20PU IC MCU 8BIT 8KB FLASH 8DIP Top
Package Included:
- ATTINY85-20PU IC MCU 8BIT 8KB FLASH 8DIP Top
ATTINY85 LilyPad Module
Features:
8K Byte of In-System Programmable Program Memory Flash
512 Bytes In-System Programmable EEPROM
512 Bytes Internal SRAM
Diameter:25mm
512 Bytes In-System Programmable EEPROM
512 Bytes Internal SRAM
Diameter:25mm
Package Included:
CJMCU-LilyTiny LilyPad ATtiny85 Development Board Professional Wearable BoardATTINY85 Black Board
Features:
Introduced the ATtiny MCU series
Art Mel ATtiny model single chip integrated with Couette Mel AVR micro controller and flash memory,
including 1KB to 4KB, with a 32 KB to 256 KB SRAM. In addition,
these devices support SPI and TWI (with the I2C- compatibility) communication,
provides maximum flexibility and the working voltage of 1.8V to 5.5V.
ATtinyAVR uses the Aite Mel patented picoPower technology,low power consumption.
Through software control system clock frequency,
to achieve the best balance between the system performance and power consumption,
but also has been widely applied.
Package Included:
ATTINY85 Micro USB Development Board Compatible Arduino NEW
ATTINY85 GY Board
Features:
100% brand new and high quality
The Digispark is an Attiny85 based microcontroller development board similar to the Arduino line,
only cheaper, smaller, and a bit less powerful.
With a whole host of shields to extend its functionality and the ability to use the familiar Arduino IDE the Digispark is a great way to jump into electronics, or perfect for when an Arduino is too big or too much.
The Digispark is shipped fully assembled except for the two included and easy to solder headers.Here are the specs:
Support for the Arduino IDE 1.0+ (OSX/Win/Linux)
Power via USB or External Source - 5v or 7-35v (12v or less recommended, automatic selection)
On-board 500ma 5V Regulator
Built-in USB
6 I/O Pins (2 are used for USB only if your program actively communicates over USB,
otherwise you can use all 6 even if you are programming via USB)
8k Flash Memory (about 6k after bootloader)I2C and SPI (vis USI)
PWM on 3 pins (more possible with Software PWM)
ADC on 4 pins
Power LED and Test/Status LED
Size:2x1.7cm(approx)
Package Included:
Digispark Kickstarter Attiny85 USB Development Board for Arduino
ATTINY85 USB Black
Features:
Brand new and high quality.
Support for the Arduino IDE 1.0+ (OSX/Win/Linux).
Power via USB or External Source - 5v or 7-35v (automatic selection).
On-board 500ma 5V Regulator.
Built-in USB (and serial debugging).
6 I/O Pins (2 are used for USB only if your program actively communicates over USB, otherwise you can use all 6 even if you are programming via USB).
8k Flash Memory (about 6k after bootloader).
I2C and SPI (vis USI).
PWM on 3 pins (more possible with Software PWM).
ADC on 4 pins.
Power LED and Test/Status LED (on Pin0).
Size: 1.8cm x 2.6cm .
Package Included:
Digispark Kickstarter ATTINY85 Arduino General Micro USB Development Board
Digispark Kickstarter ATTINY85 Arduino General Micro USB Development Board