|
|
|
|
|
|
|
|
|
Please check fitment notes & description for accurate information.
2007-2009 Acura MDX V6-3.7L Upstream
2007 Honda Odyssey V6-3.5L Upstream Rear
2008-2010 Honda Odyssey V6-3.5L Upstream Engine: J35A7
2009 Honda Odyssey V6-3.5L Upstream Rear Engine: J35A6
Oxygen Sensor's Location: How do I know the O2 sensor is good or not? Check engine light on A reduction in fuel economy.
Your catalytic converter fails unexpectedly
Exhaust emissions reach undesirable levels.
How to install the oxygen sensor? Step 1 - Some sensors are equipped with a heat shield that must be removed before the sensor removal, this is performed by removing any mounting bolts. Step 2 - By using a regular socket it minimizes potential damage to the sensor body and the threads, this technique helps avoid stripping the old sensor upon removal. Step 3 - Then, locate and disconnect the wiring connector, this step should be done before removing the sensor if the wiring is still attached. Step 4 - Its important that the wiring harness connectors are exactly the same, each sensor is unique to it's position and is located in the system by its connector configuration. (Note: some replacement sensors have a universal electrical connector that must be configured to the wiring of the old sensor.) Step 5 - Use a small wire brush to help clean the threaded port to ensure a proper seal of the new sensor. Gently install the new oxygen sensor by hand while keeping the wiring and connector free from bends. Step 6 - Gently tighten the sensor while keeping wiring free from damage, these sensors need to be fairly snug to avoid leakage. Step 7 - Once the sensor is tightened, reinstall any heat shields or bracing that had to be removed. Step 8 - After the heat shield has been reinstalled, mount the connector to it's holder and reattach the connector back onto the wiring harness. If the car has diagnostic trouble codes, they will need to be cleared. Must Know Before Buying: The following information is for instructional and guidance reference only. We try and make them as accurate as we can. If Check Engine Light is on or an OBDII Trouble/Fault code occurs after installation, check the sensor with a voltmeter as below. If the sensor is good, further diagnosis is required. There're many different codes for specific functional failures, which are NOT necessarily relevant to the sensor. Find out what the Code means before leaving any feedbacks. Items that have been installed, altered or contaminated are non-returnable. 1. ONLY a defective sensor after tested by a voltmeter is applied to manufacturer warranty. 2. 20% restocking fee is required if buyer bought wrong items due to not paying attention to fitment information and ask for return. The Price, Quality & Functionality of the O2 Sensor is fully covered under our warranty & return policy. However, refund for any labor cost, expense in a dealer shop or damage due to wrong installation is NOT covered.
Item Specifics | |
---|---|
Manufacturer Part Number | AUT0661670US |
Type | Air Fuel Ratio Sensor |
Brand | AutoDealsParts |
Manufacturer Warranty | 1 Year |
Interchange Part Number | o2 sensor, 02 sensor, oxygen sensor car, wideband o2 sensor |
Other Part Number | 13954A, 250-25056A |
Superseded Part Number | 2345053-A, 13954-A, 75-3829-A, 75-3830-A, 24346-A |
Custom Bundle | No |
Modified Item | No |
Number of Pieces | 1 |
Fitment Type | Direct Replacement |
Thread Size | M18 |
Terminal Type | Blade |
Universal Or Specific Fit | Specific |
Attachment Method | Screw-On |
Connector Gender | Male |
Wire Harness Length | 12.8 IN |
Sensor Type | Heated |
Wire Quantity | 5 |
Output Signal Range | 0.2V To 0.8V |
Mounting Type | Threaded |
Pin Quantity | 5 |
Position | Upstream, Sensor 1 |
Feature | ESCP |
Type | Sensor |
Features | Direct Fit |
We only accept PayPal.
1. We only ship to confirmed paypal addresses, your paypal address must match your shipping address.
2. All domestic orders will be shipped via USPS, UPS or Fedex from our US warehouse and usually arrives to your door in about 2-7 business days.
3. If you have not received your shipment within 15 days from payment , please contact us. We will track the shipment and get back to you as soon as possible with a reply.
4. Local pick up is not available.
All of our brand new items come with a 30-days money-back guarantee.
If you have any question, please contact us.
Cancer and Reproductive Harm - www.P65Warnings.ca.gov.
Autodealsparts
Shop Category Picture Picture Picture |
Oxygen Sensor O2 Air Fuel Ratio Sensor for 2007 Honda Odyssey 3.5L Upstream Rear
Please check fitment notes & description for accurate information. 2007-2009 Acura MDX V6-3.7L Upstream 2007 Honda Odyssey V6-3.5L Upstream Rear 2008-2010 Honda Odyssey V6-3.5L Upstream Engine: J35A7 2009 Honda Odyssey V6-3.5L Upstream Rear Engine: J35A6
Oxygen Sensor's Location: How do I know the O2 sensor is good or not? Check engine light on A reduction in fuel economy. Your catalytic converter fails unexpectedly Exhaust emissions reach undesirable levels. How to install the oxygen sensor? Step 1 - Some sensors are equipped with a heat shield that must be removed before the sensor removal, this is performed by removing any mounting bolts. Step 2 - By using a regular socket it minimizes potential damage to the sensor body and the threads, this technique helps avoid stripping the old sensor upon removal. Step 3 - Then, locate and disconnect the wiring connector, this step should be done before removing the sensor if the wiring is still attached. Step 4 - Its important that the wiring harness connectors are exactly the same, each sensor is unique to it's position and is located in the system by its connector configuration. (Note: some replacement sensors have a universal electrical connector that must be configured to the wiring of the old sensor.) Step 5 - Use a small wire brush to help clean the threaded port to ensure a proper seal of the new sensor. Gently install the new oxygen sensor by hand while keeping the wiring and connector free from bends. Step 6 - Gently tighten the sensor while keeping wiring free from damage, these sensors need to be fairly snug to avoid leakage. Step 7 - Once the sensor is tightened, reinstall any heat shields or bracing that had to be removed. Step 8 - After the heat shield has been reinstalled, mount the connector to it's holder and reattach the connector back onto the wiring harness. If the car has diagnostic trouble codes, they will need to be cleared. Must Know Before Buying: The following information is for instructional and guidance reference only. We try and make them as accurate as we can. If Check Engine Light is on or an OBDII Trouble/Fault code occurs after installation, check the sensor with a voltmeter as below. If the sensor is good, further diagnosis is required. There're many different codes for specific functional failures, which are NOT necessarily relevant to the sensor. Find out what the Code means before leaving any feedbacks. Items that have been installed, altered or contaminated are non-returnable. 1. ONLY a defective sensor after tested by a voltmeter is applied to manufacturer warranty. 2. 20% restocking fee is required if buyer bought wrong items due to not paying attention to fitment information and ask for return. The Price, Quality & Functionality of the O2 Sensor is fully covered under our warranty & return policy. However, refund for any labor cost, expense in a dealer shop or damage due to wrong installation is NOT covered. Payment
We only accept PayPal. Shipping
1. We only ship to confirmed paypal addresses, your paypal address must match your shipping address.
Returns
All of our brand new items come with a 30-days money-back guarantee. Contact Us
If you have any question, please contact us. Warning
Cancer and Reproductive Harm - www.P65Warnings.ca.gov. All rights reserved. |