About this item:

  • 🌐100Mpbs Bridge: Wireless bridge kit has 2 100Mbps RJ45 port, the wired network speed up to 100 Mbps. The transmission rate between the two wifi bridges is up to 300Mbps, transmission/receiver automatic networking, support point-to-point, point-to-multipoint, transmission/receiver flexible switching. WDS networking mode, video network dual compatible
  • 🌐Up to 3KM : High gain 14 dBi integrated directional antennas built into the device extends networks up to 3 KM. The actual application transmission distance should be less than 3KM (barrier-free). A few trees will not reduce the transmission speed of CPE
  • 🌐Plug and Play: CPE402 is powered by a 24V Poe adapter(included) and supports dial pairing without entering the GUI. The bridges are pre-configured, just connect the Poe power supply to achieve automatic pairing of the two bridges. It not only can help extend your home's network to the second building but also can be used for monitoring
  • 🌐Building to Building Extend the Network: You can extend your house's network to your garage, barn, store, warehouse, farm, etc. with the wireless bridge, wildly use in daily life. Helping you save money
  • 🌐5.8G Technology & IP65 Waterproof: Long range wifi bridge using 5.8G IEEE 802.11ac single-band wireless transmission technology, with better anti-interference performance, good compatibility, strong anti-adjacent channel interference, better than 2.4G traditional CPE. This wifi bridge kit is IP65 waterproof, dustproof, cold-proof, and heat-resistant
 

Product Description

wireless bridge point to multipoint

100Mbps Wireless Bridge Extend the Network Building to Building, Long Range Wireless Bridge Supports 3KM

ULNA CPE402 is a 100Mbps wireless bridges. It uses wireless communication technology to transmit network data using air as a medium, one as a transmitter and the other as a receiver for long-distance point-to-point or point-to-multipoint interconnection. For example, extend your network from the main house to the garage, barn, store, warehouse...

Easy to Use

1. Unbox everything

2. Switch one unit to A and one unit to B

3. Connect the POE to each unit using the Ethernet cable and plug the POE in

4. Wait for them to power up, about 2 min

5. For 5.8 gh Use the tiny reset button to click through until you get a channel with a letter. A,B,C… Then on the other unit do the same. Both units need to be on the same channel

6. You should see them sync

7. Place the unit you designated B in step 2 above at the existing WiFi point and the unit designated A at the location you are trying to establish extended WiFi

8. Plug at cable from your router to the POE then to the unit

9. At the far end plug a cable in the unit, then to the POE then another cable from the POE to your new router

10. Enjoy

Supports Point-to-Point and Point-to-Multipoint

dialing wireless bridge kit
point to point wireless wifi bridge

Connection Guidelines

The master(A:transmitter）and slave（B:receiver) bridges should be installed face to face, the antenna is not omnidirectional, it has a 60 degree transmission angle, a straight line installation with no obstructions will be the best performance

wifi bridge with ethernet port

wireless bridge poe

cpe wireless bridge

Switch Master-Slave Bridge

Switch button to"A" indicates the bridge as the master bridge (transmitter), switch button to"B" indicates the bridge as the slave bridge (receiver), a pair of bridges is already preset with A and B, no need to set them again. Note that in the point-to-multipoint application, one of the bridges is used as A and the other bridges are used as B. Then set them both to the same channel number to complete the point-to-multipoint pairing

Elevator Monitoring Applications

Using a ethernet wireless bridge to transmit monitoring signals in elevator monitoring provides stable surveillance images and prevents cable damage. In addition, ethernet bridges are easy and fast to install and can be disassembled for reuse, making them ideal for elevator monitoring

Watchdog Function

Wireless bridge with watchdog function. When wifi bridge ethernet communication fails, the corresponding unit will turn on automatic detection and restart, thus restoring network communication by
 

lan wireless bridge

p2p wifi bridge

p2p wireless bridge

Suitable for Outdoor Use

The high speed wireless bridge is IP65 dustproof and waterproof, and has anti-freeze function, suitable for working temperature: -4℉～158℉, suitable for outdoor use

Easily Setup

Use the metal ties (included) to attach the ethernet wireless bridge to the bracket or hang it on the wall. Recommended ULNA Universal Bracket (ASIN: B0BCNZFNTD).

Tip: Install the 2 wireless bridges facing each other as much as possible with a clear and unobstructed view

Features

100Mbps Ethernet port

14dBi antenna

5.8G channel

Transmission distance up to 3 km

Support PC side to modify IP settings

Dialing to set the transmitter and receiver

WDS networking mode, video network dual compatibility

Dynamic MIMO power saving mode (DMPS) and automatic power saving transmission (APSD)
 

Clear and Stable Video Transmission

preconfigured wireless outdoor bridge

Am 29.11.2023 hat der Verkäufer die folgenden Angaben hinzugefügt:

DataCaciques