About this item
-
Easy to Pair: CPE966 Wireless bridge adopts AB automatic networking. Just transfer one end to A as the master bridge and the other end to B as the slave bridge, then you can easily configure it without entering the GUI. This wifi wireless bridge support point-to-point, point-to-multipoint pairing
-
High Speed: This outdoor point to point wireless bridge has one Gigabit RJ45 port and a 100Mbps RJ45 port. The transmission speed between the two wifi bridges outdoor is up to 1200Mbps. Through the Gigabit RJ45 port, the maximum wired network speed will be 433Mbps, Which can better meet your internet speed needs
-
3KM Working Distance: Outdoor wireless bridge is a built-in 16DBi directional antenna, which can significantly improve the signal quality. The actual application transmission distance should be less than 3KM (barrier-free). Trees will not block the transmission speed of a point-to-point internet outdoor CPE
-
5.8G Technology & IP65 Waterproof: Long range wifi bridge using 5.8G IEEE 802.11ac single-band wireless transmission technology, with better anti-interference performance, good compatibility, strong anti-adjacent channel interference, better than 2.4G traditional CPE. This point to point wireless wifi bridge is IP65 waterproof, dustproof, cold-proof, and heat-resistant
-
Good Choice for Daily Use: Wifi bridge point to point outdoor can be used wildly in daily life. It not only can help extend your home's network to a second building but also can be used for monitoring. And you can use it in the garage, barn, store, warehouse, farm, and some other place according to your convenience
Product Description
Gigabit Wireless Bridge High-speed Internet
Application Case1:
I needed high speed internet about 350 feet away from my house. It only took six minutes to get this system set up and running. I'm glad I paid a little extra and went with this 1Gbps model versus the slower 100Mbps model. The receiving bridge gets 285.38 Mbps download speed and 159.87 Mbps upload speed. I'm on Starlink in a very remote location. I do not notice any slowdown at all from my house speeds. I do have direct line of sight.
I also bought a second set, and have hooked them all together. One of the units was set up as the master and the other three were set up as remote receivers. I are only covering distances of about 350 yards, but I have no doubt that the system would handle much longer distances without problem. Throughput to all three remote locations is great, even when streaming video on all three.
Recommended ULNA wireless bridges
Easy to Use
1.Unbox everything
2. Switch one unit to A and one unit to B
3. Connect the POE to each unit using the Ethernet cable and plug the POE in
3. Wait for them to power up, about 2 min
4. For 5.8 gh Use the tiny reset button to click through until you get a channel with a letter. A,B,C…I used C. Then on the other unit do the same. Both units need to be on the same channel
5. You should see them sync
6. Place the unit you designated B in step 2 above at the existing WiFi point and the unit designated A at the location you are trying to establish extended WiFi
7. Plug at cable from your router to the POE then to the unit
8. At the far end plug a cable in the unit, then to the POE then another cable from the POE to your new router
9. Enjoy
Wireless Bridge Detail
|
|
|
|
|---|---|---|
Only One 1Gbps PortThe gigabit wifi bridge has 1 100Mbps and 1000Mbps ports, both of which can accept a 24V PoE power supply, recommended to connect a gigabit port, and the CAT 5e network cable can be used as a power cable to supply power and transmit data. DC power supply is not recommended. Tip: only the PoE port supplies power |
Dialing PairingThe wifi bridge ethernet pairing can be done by dialing without having to access the GUI, plug and play. Switch button to"A" indicates the bridge as the master bridge (transmitter), Switch button to"B" indicates the bridge as the slave bridge (receiver) |
Package Included2 x CPE966 1Gbps wireless bridge 2 x PoE Adapter 2 x Network Cable 2 x Metal Cable Tie 1 X User Manual |
|
|
|
|
|---|---|---|
5.8G Wifi Bridge Outdoor2.4G channel is used by a large number of people, anti-interference is poor, slow transmission and easy to drop, 5.8G channel is used by a small number of people, the channel is more pure, anti-interference ability is better, faster and farther transmission |
Easy InstallationUse metal ties (included) to secure the ethernet bridge wireless to the bracket or hang it on the wall. Tip: Install the 2 wireless bridges facing each other as much as possible with a clear and unobstructed view. Recommended ULNA Universal Bracket (ASIN: B0BCNZFNTD) |
FeaturesGigabit port 16dBi antenna 5.8G channel Transmission distance up to 3 km Support PC side to modify IP settings Dialing to set the transmitter and receiver WDS networking mode, video network dual compatibility Dynamic MIMO power saving mode (DMPS) and automatic power saving transmission (APSD) |
Clear and Stable Video Transmission
Am 28.08.2023 hat der Verkäufer die folgenden Angaben hinzugefügt: