Key Features:
One-piece structure, Super printing size 220*220*250mm.
Comes with several assembled parts, simple assembly, only 120 minutes for 3D printer beginners before the first printing.
Big hand twist nut, easier to level.
Safety protected Power supply, reach 110℃ for hotbed in about 5 minutes.
The resume printing function can resume prints even after a power outage or lapse occurs.
Product description:
3D Technology： FDM
Max Traveling Speed：180mm/s
Filament：1.75mm PLA
Layer Thickness：0.1-0.4mm
Nozzle diameter：0.4mm
Precision：±0.1mm
Input：AC 100-265V 50-60Hz
Output：DC 24V 15A 360W
Max Nozzle Temperature：255℃
Max Hot bed Temperature：110℃
Printing Size：220*220*250mm
Machine Size：440*410*465mm
Package weight：8.6kg
File Format： STL, OBJ, G-Code
Working Mode： Online or SD offline
Package content:
FAQ
Filament does not stick on the hotbed?
For newcomers, this is the most common problem. Do not worry, you can solve it easily. Generally, the distance between the nozzle and platform is too far or near. So rotary the knob under the platform to adjust the distance between the nozzle and platform again, at a piece of A4 paper distance or less).
The display shows "Min temp"?
This happens for the following reasons: 1. Thermistor port of nozzle is not plugged into the motherboard above or poor contact; 2. The Thermistor port of the nozzle is broken, you need to replace the spare thermistor.
The display shows "MAX temp"?
This happens for the following reasons:
1.Thermistor port of nozzle screw is locked tightly, cause the temperature can not be sensing;
2.Thermistor port of the nozzle is broken, you need to replace the spare thermistor.
Axis movement is not normal?
Please check axis lines and limit lines whether the one-to-one correspondence, whether loose. When you check the extruder motor, you must preheat the nozzle over 185℃.
Circles not round, Lines not touching?
If the X/Y belt is loose, you can find circles that are not round, Lines not touching when printing. Tighten all belts as far as possible.
How to level Creality Creality Ender 3?
- Move the nozzle so that it’s positioned over the left corner of the bed. A half-inch or so from both sides is a good location.
- Slide the paper between the nozzle and the bed. If it doesn’t fit, drop the corner until it does.
- Once the paper is able to slide under the nozzle, very slowly raise the corner with the adjuster. Remember: Clockwise moves the bed up. As you do this, gently slide the paper back and forth. The moment you feel even the slightest resistance to your moving the paper, stop turning the knob. That corner is (almost) ready to go.
- Do the same for the other three corners of the build plate. Always advance the hot end to a new corner slowly. This will prevent damage to the build plate in case the nozzle starts to drag. If this occurs, simply lower the next corner (before starting the leveling process) to make some room.
- After you’ve adjusted each corner once, go back and check the four corners again. You may have to do further adjustments to get all four correct.
Does Creality Ender 3 need to be assembled all by itself?
No, Ender 3 is a semi-assembly machine. You can refer to our packing instructions for assembly. Its installation is quite simple.
The specific installation time depends on the user's familiarity with the product. If you are familiar with the product and can fully understand the installation instructions, it will take about 30 minutes. If you don't know much about a 3D printer, it takes about two or three hours.
PLA，PETG，ABS
Step 1:Adjust the nozzle temperature to the consumable melting temperature and remove the consumables to be replaced.
Step 2:Push the new filament along until you feel firm resistance. This means it has reached the nozzle.
Step 1:Set the heating temperature, eliminate old consumables, and make new prints.
