Good News: New items have arrived Germany warehouse, welcome you to purchase.
We have Germany Warehouse in Germany,so we can ship from Germany to European Union Customers.1 x 4.5KW BT30 ATC Automatic Tool Change Air Cooled Spindle Motor 220V ( 24000rpm, 15A,3-phase,800Hz, 4pcs bearing )
2 x Aviation plug
1 x 5.5KW Fuling VFD Inverter 220V
1 x BT30-ER25 Tool Holder with pull stud
English user manual will send by email
2)The bearing of spindle use grease lubricated angular TOcontact bearings,can be achieved lifelong lubricating within the life cycle.
3)The spindle use forced coolling mode TOcoolling motor,front and rear bearings.Coolant flow through the reasonable arrangement cycle watercourse of the spindle body,thus can take the heat generated of the spindle rotation speed, TOachieve thermal equilibrium,let spindle temperature within a certain constant value. External coolingDevice effect:maintaining a constant temperature of the coolant.
4)The spindle built-in PTC 140 temperature sensor(TEchnicalparameters are visible in other sections of this specification),you can read it anytime if you need TOprotect the motor temperature.
5)The tool clamping methods:this spindle built-in automatic tool changeDevice,shank form is BT1.
SpindlemODEL: | RTM120X103-30-24Z/4.5220v | Voltage: | 220V |
Maximum speed: | 24000rpm | rated frequency: | 800HZ |
Electric current: | 15A | Motor Pole: | 4 Pole |
RAted power: | 4.5KW(S1) | Peak power: | 5.4KW(S6) |
Rated Torque: | 3.5NM | Peak Torque: | 4.2NM |
Productcharacteristic curve graph:
Wiring definition
Power Supply, Fhermal, Fan
Proximity switch and push button switch
Details:
TEchnicalparameters | ||
No. | PRoject | Standard |
1 | SpindleblowingDust/seal gas pressure (MPa) | 0.2-0.25 |
2 | Spindlegas seal gas flow (L/min) | 65 + 10 (When onWORKING) |
3 | Cooling water pressure (MPa) | ≧0.25 |
4 | Cooling water flow (L/min) | ≧2.5 |
5 | Cooling water temperature(℃) | 24-28 |
6 | Spindlestatic state pulse(M) | ≦3 |
7 | Spindlevibration (Mm/s) | ≦1.0 |
8 | Spindleassembly method | Bottom mounting(6-M8) |
9 | MotorwindingsPressure test (V/M) | 1000V/1 minute withstanding Voltage test |
10 | Tool Interface | BT1 |
11 | Inverter Specifications | 5.5KW(220V) |
12 | fitment | Woodworking machinery, polishing industry, etc. |
Spindleinstallation explanation
1) Fan cooling systemDescription
When the spindle rotates, the rear fan system must be started TOensure the correct supply voltage and the supply voltage is 12v.
2) Air Sealing control(AS)
In
order TOprevent water or impurities enters internal of the
spindle,spindle will have gas SealingDevice,the gas seal machine must be
started start with the machine at the same time. And the need TOgo
throughmulti-stage filtration.
3) Compressed gas quality requirements
The quality requirement of gas whichis used in gas seals:
Oil Content:﹤0.01mg/m³
Solid particle:< 5 * m
PressureDew point:< 7.5Degrees C(0.7mpa)
4) Running-in program instructions
Only all monitoring issued no failures operational signals,at the same time,all safetyDevices have been installed and working properly,then allow start spindle.
Note: new
or spindlewhichIs not used for a long time must TObe running
slowly.First,start run spindle for half an hour as 25% of the maximum
speed,then increase TO50% of the maximum speed,TOrun 15
minutes,finally, increase TOmaximum speed.It 's need TOcheck the
temperature of the spindleDuring the wholeProcess,Spindle will get hot,
but not hot hand, if the spindle becomes hot, pls stop the operation and
contact our customer serviceDepartment.
5) Productbackend interface instructions
No. | Function | DEfinition |
1 | GAS Sealing(Protection of impurities inTOthe spindle0.2-0.25MPa) | Ф6 |
2 | Return air (piston reset 0.35-0.45MPa) | Ф6 |
5 | Power Supply (Spindlepower lines with thermistor) | U/V/W/ Ground wire |
6 | Intake air (Spindleloose knife0.5-0.6MPa) | Ф6 |
7 | sensor(spindle tool change signals 24V) | Broach / loose knife |
8 | Fan(spindle cooling) | 12v |
6) PTC140Temperature coefficient thermistor parameters
Our products are equipped with a single thermistor PTC140, it can be used for spindle temperature protection.
Parameter name | Parameter symbol | Single Core | Three core Series connection | Unit |
Maximum DC working temperature | Umax | 30 | 30 | V |
Rated control temperature | TK | Designed according TOuser | ℃ | |
Rated control temperaturetolerance | T1 | ±5℃ | ±5℃ | ℃ |
Rated control temperaturetolerance | T2 | ±0.5℃ | ±0.5℃ | ℃ |
Resistance value on 25℃ | r25 | ≤100 | ≤300 | Ω |
Rated control temperature | TK-5℃ | ≤550 | ≤1600 | Ω |
Rated control temperature | TK+5℃ | ≥1330 | ≥4000 | Ω |
Rated control temperature | TK+15℃ | ≥4 | ≥12 | KO |
Thermal response time | TA | ≤5 | ≤5 | S |
Dielectric Strength | Uis | AC2.5 | AC2.5 | KV |
Maximum control temperature | TKmax | 180 | 180 | ℃ |
Maximum allowable storage temperature | tmax | 180 | 180 | ℃ |
Minimum allowable storage temperature | Tmin | -40 | -40 | ℃ |
7) ProductTool ChangeSignalsdescription
sensor MODEL(0-24V, PNP), The spindle built two sensors.wiring Diagram is as follows:
1. Response broach knife signal, when theKnife handleIs hang,black sensor output signal;
2. Response loose knife signal, when theKnife jawsOpen,black sensor output signal;
5.5KW Fuling Inverter VFD 220v
Feature:
It could adapt TOtheDust working environment.
Output frequency:0-1000hz
220V Configuration:
Brand Name:Fuling
Power:5.5kw
Rated output current:23A
Output voltage:3phase AC220V
Input voltage:1phase AC220V
Frequency:0-1000HZ
380V Configuration:
Brand Name:Fuling
Power:5.5kw
Rated output current:23A
Output voltage:3phase AC380V
Input voltage:3phase AC380V
Frequency:0-1000HZ
The usages of the product and warnings
Matters need attention when you install this spindle
1. When installed, please carefully, pay attention to personal safety and to avoid injuries occurred during the installed process;
2. Do not use any tools tapping spindle;
3. Do not use sandpaper and grinding wheel to wipe or grind in axis core and taper hole;
4. Use special removal tool to remov the lock nut and the tool;
5. Untrained personnel can not disassemble and operate electric spindle;
Attention to maintenance and maintenance
1. Electric spindle storage temperature is 20 ℃ ± 10 ℃, humidity ≦ 85%, to allow time to store up to three months;
2. Electric spindle most suitable ambient temperature is 20 ℃ ± 10 ℃, bearing life can achieve the desired optimum value;
3. The power cord must take waterproof measure, electric spindle housing must be grounded;
4. Electro-spindle must not exceed nameplate parameters;.
5. Not allowed to use any mechanical way to forced braking in the shaft;
6. after using the spindle every day,you should wipe spindle taper,then smear with rust oil;
7. Workplace must be clean, there should be strict dust control measures to prevent foreign matter enter the spindle.
Product common malfunctions&method of exclusion
Fault phenomenon | Reason | Method of exclusion |
Electric spindle is not running after boot | 1、No inverter power output or set incorrectly | Check that VFD supply three-phase output voltage and setting method |
2、Spindle plug is not inserted | Check the electrical spindle plug and connection. | |
3、Bad plug connector | ||
4、Bad stator line package | Replace line package | |
Shutdown after a few seconds of the boot | 1、Start time is too short | Increase the acceleration time |
2、Electric spindle high temperature cause line package insulation damaged | Replace line package | |
3、Electric spindle lose phase to run,then cause overcurrent protection blackout | Check the electric spindle connection | |
Electric spindle smoking or the housing hot after a few second of the boot | 1、Inverter output voltage, frequency are not match the use of electric spindle voltage and frequency | Check the VFD and the spindle voltage, frequency |
2、The VFD is not set correctly | Reset the VFD | |
Locking nut loose when it is started | Wrong direction of rotation | Change the direction of rotation |
Spindle have big noise and vibration | 1、Bearing wear seriously | Replace the bearing |
2、Precision of parts damaged,it’s effect dynamic balance | Calibration of dynamic balance | |
3、Big beat of Spindle | Replace the spindle | |
Locking nut loose when it is stoped | Stop time is too short | Increase the deceleration time |