Product Details
New update to PCB 5.0T-2013
New features:
Enhanced 3.6V power supply.
Use CMOS voltage regulator IC to get 3.3V low voltage
This ready-to-go package includes everything you need to get your project start rolling:
1. Willem Universal E(e)prom Programmer Board, PCB version 5.0E SMD version, fully assembled
2.clip PLCC32+SOIC 8 pin adapter+USB cable+Computer cable (DB25)
Device types supported
SPI Flash Bios chips support added !
SPANSION
S25FL004A/040A,S25FL008A,S25FL040A-T,S25FL040A-B,S25FL016A,S25FL032A
S25FL064A
WINBOND
W25X010,W25X020,W25X040,W25X080,W25X16,W25X32,W25X64
MXIC
MX25L512,MX25L1005,MX25L2005,MX25L4005A,MX25L8005A,MX25L1605,MX25L3205
MX25L6405
EON
EN25B05,EN25B10,EN25B20,EN25B40,EN25B80,EN25B16,EN25B32,EN25B64
EN25P05,EN25P10,EN25P20,EN25P40,EN25BP80,EN25P16,EN25P32,EN25P64
EN25D80,EN25D16,EN25F20,EN25F40,EN25F80,EN25F16
AMIC
A25L05P-B,A25L10P-B,A25L20P-B,A25L05P-T,A25L10P-T,A25L20P-T,A25L512
A25L010,A25L020,A25L040,A25L080;,A25L016,A25L032
pFLASH
Pm25LV512,Pm25LV010,Pm25LV020,Pm25LV040,Pm25LV080,Pm25LV016
Numonyx (ST)
M25P05,M25P10,M25P20,M25P40,M25P80,M25P16,M25P32,M25P64
M25PE10,M25PE20,M25PE40,M25PE80,
**M45PE10,M45PE20,M45PE40,M45PE80,M45PE16
M25PX80,M25PX16,M25PX32,M25PX64
ATMEL
AT25DF021,AT25DF041A,AT25DF081,AT25DF081A,AT25DF161,AT25DF321A
AT25DF641,AT26DF041,AT26DF161A,AT26DF321,
** AT45DF011D,AT45DF021D,AT45DF041D,AT45DF081D,AT45DB161D,AT45DF321D,AT45DF641D
EPROM |
27C64, 27C128, 27C256, 27C512, 27C010, 27C020, 27C040, 27C1001 |
EEPROM |
28C65,28C64, 28C128, 28C256,28C512, 28C010, 28C020, 28C040 |
FLASH Memory |
28F64, 28F128, 28F256, 28F512,28F010, 28F020 |
FLASH Memory |
29F64, 29F128,29F256, 29F512,29F010, 29F020, 29F040, 29F080 |
Serial (I2C) EEPROM |
24C02,24C04,24C08,24C16, 85C72, 85C82, 85C92 |
Microwire EEPROM |
<------ Data 8bit -----> (pin 6 ->ORG. [Schematic connect to GND]) |
MicroChip PIC |
16C84 , 16F84 ,16F84A , 16F627/16F628 |
Atmel Flash Memory |
AT29C256, AT29C512,AT29C010A, AT29C020, AT29C040,AT29C040A
W29EE512,W29EE011, W29EE012, W29C020(128),W29C040 PH29EE010(W29EE011) ASD AE29F1008 (AT29C010), AE29F2008 (AT29C020) |
Atmel Flash Memory |
Command seq. 5555/AA, 2AAA/55, 5555/A0 |
Serial Peripheral Interface (SPI) |
[Atmel] AT25010,020, 040 (A8-A0)
AT25080, 160, 320, 640, 128, 256 (A15-A0) [ST] W95010....256, Microchip 25x010 - 25x640 --- Byte programming -- CAT64LCxxx (16bit DATA IN/OUT) use Socket 93Cxxx |
Atmel EEPROM (page prog.) |
AT28C256, AT28C010, AT28C040 |
Nonvaltile SRAM (DS12xx) |
DS1220,DS1225Y, DS1230Y/AB, DS1245Y/AB, DS1249Y/AB |
static RAM (Test RAM) |
6116, 6264, 62256, 62512, 628128 |
EPROM winbond,SST |
W27E512, W27E010, W27C010, W27C020, W27C040 |
Flash Memory SST,Sanyo |
SST28SF040A ,LE28F4001 |
|
|
Atmel AT89Cxx (MCS-51) |
Atmel Auto Setect |
Atmel AVR 8-bit RISC AT90Sxxx |
(read,write,erase,verify,checkempty,Lockbits ,Fusebits) [Flash memory/EEPROM] |
MCS-48,MCS-41 |
ROM (read/verify)
P8048AH, P8049AH,P8050AH, P8042AH Vea = 12V P8041, P8042 OTP (read/verify/Progam) EPROM (read/verify/Progam) |
FLASH memory 8/16bit |
Am29F400,Am29F800,29F160,29F320 (read,write byte mode) |
FLASH memory 8/16bit (Vpp12V) |
i28F200,i28F400,i28F800,i28F160 (TSOP48) |
EPROM 16bit (DIP40) (1-4Mbit) |
27C1024 (27C210), 27C2048 (27C2002), 27C4096 (27C4002), |
EPROM 16bit (DIP42) (4-32Mbit) |
M27C400(DIP40), 27C800, 27C160, 27C322 |
FLASH memory 8/16bit |
29LV200, 29LV400,29LV800,29LV160,29LV320 (read,write byte mode) |
Firmware Hub / LPC FLASH |
-- Firmware Hub
82802AB, 82802AC, AT49LW040, AT49LW080 SST49LF002A, SST49LF003A, SST49LF004A, SST49LF008A, PMC 49FL008T W49V002FA, W39V040FA -- LPC flash |
P28F002BC |
BOOT BLOCK FLASH MEMORY |
EPROM Programmer PCB5.0E ( NEW!!! Developed Board (October 2009)) |
. Upgrading, Programming BIOS chip, Repairing PC motherboard BIOS chip. |
|
1. We only ship to the confirmed address provided by eBay. please make sure your ebay address is 100% matches the address you would like us to ship to. If not, please let us know before we sent you the package, or we will not be responsible for any loss. hope you could understand.
2. Orders will be processed instantly and dispatched within 1-3 business days except hoilday, so we do NOT accept any email/message note after you place orders.
3. All package need to wait 30 days,Please take care it.Less than 30 days,we can't take a refund.
We maintain high standards of excellence and strive for 100% customer satisfaction! Feedback is very important to us. We request that you keep in touch with us immediately BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concerns.