Rated wind power

600W/12V,800W/24V,1000W/48V

Rated PV power

1000W/12V,1500W/24V,2000W/48V

Product introduction

This kind of wind-solar hybrid charge controller is specially designed for small off-grid wind

Generation and solar hybrid system. Appearance is elegant, operations are simple. It also makes the

Expiration, in which wind generator and solar panels charge batteries safely and efficiently.

Functions and Features

Wind generator MPPT boost charging function, improved charging efficiency . 

External dump load resistant to strong wind, work more stable. Solar MPPT charging, 

solar intelligent separation charging, high efficiency charging. 

Dual power supply function: battery and solar power supply. LCD shows parameters such as voltage 

and current of wind, solar and load.

Some parameters can be set by users. 

DC output with three output modes. Battery module type can be selected and parameters can be set;

The controller has a built-in dust net that is easy to replace and clean to ensure the service life of the controller. 

The inner circuit board of the controller is sprayed with conformal coating to prevent

Prevent dust, moisture and static electricity 

Solar energy protection:As in the night, the voltage of the battery can be higher than the solar panel. 

Thecontroller protects the battery from charging the solar panel.

Battery protection: if the battery polarity is reversed, the controller will not work and there will be no display. 

The fuse protects the internal circuit. 

If the battery does not work properly after it is connected properly, you only need to replace the fuse.

Battery open circuit protection: after long time use, the battery may be open circuit or bad connection. 

The controller can protect itself from damage. Check the connection regularly

Over-voltage Over-current : When it is strong wind or over-voltage, the controller will 

automatically start the braking function to protect the wind generator and the battery. 

The controller will automatically break the circuit when the output is overvoltage.

Lightning Protection: Lightning protection refers to the last level of protection required for equipment.

Special lightning protection devices and other components of the multi-level lightning protection 

system are required for lightning-prone areas. If the user requires this function, it must be paid additionally.

Introduction of the MPPT

The Maximum Power Point Tracking (MPPT) system is an advanced charging technology that

Enables solar panels to output more power by adjusting the operating state of electrical modules. 

Because of the nonlinearity of a solar array,there is a maximum energy output point (maximum 

power point) on the curve of the array. 

Traditional solar charge controller (switch charge technology and PWM charge Technology) can not 

charge batteries at this point, therefore, unable to obtain the maximum energy of solar energy Plates. 

However, the solar charge controller equipped with MPPT control technology can.

Track the maximum power point of a solar system at any time to obtain maximum energy for battery

Charge. 

Take the 12V system for example. 

The peak voltage of solar panels (Vpp) is about 17V and Battery voltage is about 12V. 

In general, when the solar charge controller charges a battery.

Solar panel voltage is maintained at about 12V, which means the maximum power is not consumed.

MPPT solar charge controllers provide a solution to this problem by constantly adjusting the input

Voltage and current of solar panels, maximizing the input power.

Compared to traditional PWM solar charge controllers, MPPT solar charge controllers bring you

Utilize the maximum power of solar modules and provide higher charging current. 

In general:

MPPT solar charge controllers can improve the energy utilization rate by 15% ~ 20% compared with 

PWM solar Charge Controllers. 

In addition, different ambient temperature and lighting conditions will cause frequent changes in the

the maximum power point. 

Our MPPT solar charge controller can adjust parameters constantly According to different conditions 

to constantly place the system near the maximum operating point.

The whole process is fully automatic without any adjustment by the user. 

 WIND+and WIND input terminals are the DC input terminals of the generator after rectification by the 

internal rectifier circuit of the controller. 

BAT+and BAT: are battery storage connection terminals.

L1 is the MPPT power inductor used to store energy during MPPT charging.

D1 is a reverse isolation protection diode that can reduce the loss caused by the line of the Switch.

Translated with www.DeepL.com/Translator (free version)

Q1 is a switching MOSFET, which is the core component of the MPPT circuit. It controls the operation of 

the MOSFET via a high-frequency PWM drive waveform, which causes the fan to operate at Maximum 

Power Operating Condition.

Due to the constant changes in wind speed and direction of the natural wind, timely tracking and adjustment 

are required. 

According to the generator input signal sampled by the controller, the circuit adjusts the drive waveform 

of MOS tube Q1 in real time by MCU analysis and control and MPPT software algorithm, achieving 

instantaneous response and MPPT charging effect.

The ordinary charge controller of the wind turbine can only be charged when the fan is large and the fan

Voltage is higher than the battery voltage. 

The MPPT controller of this product can not only meet this requirement, but also realize the breeze 

charging function by increasing the lower fan input voltage through the MPPT boost circuit when the wind 

power is low and the fan input voltage is lower than the Battery voltage and allow the fan to operate at 

the maximum power point.