About this item

🌐【High Speed】Wireless bridge set 27 dBm high wireless transmit power extends Wi-Fi building-to-building, transmission speed between 2 bridges max is 1200Mbps. The highest network speed that can be achieved is 433Mbps. Transmission/receiver automatic networking, support ptp/ptmp. WDS networking mode, video network dual compatible
🌐【5KM Transmission Distance】This wifi outdoor bridge built-in 16dBi directional antenna can effectively improve the transmission and reception performance of wireless signals. It supports 5KM long-distance wireless transmission. Wireless outdoor bridge can be widely used in daily life. Ideal for warehouses, gardens, barns, offices, shops, or garages next to your home
🌐【5.8G Technology】The 5.8G frequency adopts 11ac technology, which is better than 2.4G traditional CPE. It has better anti-interference, compatibility, and strong anti-adjacent channel interference. High-quality ABS material can resist rain, thunder, frost, and sun. Good choice for daily use
🌐【Plug and play】CPE609 is powered by a 24V Poe adapter(included) and supports dial pairing without entering the GUI. wifi bridge kit are pre-configured, just connect the Poe power supply to achieve automatic pairing of the two bridges. It not only can help extend your home's network to the second building but also can be used for monitoring
🌐【Customer Service】Wireless bridge poe suitable for users who need to extend their network from one building to the next building within 5KM. If you have any problem, feel free to contact us, ULNA will do our best to help you solve the problem to your satisfaction

Product Description

Long Range WiFi Wireless Bridge Supports 5KM

ULNA CPE609 is a 1Gbps wireless bridges. It uses wireless communication technology to transmit network data using air as a medium, one as a receiver and the other as a transmitter for long-distance point-to-point or point-to-multipoint interconnection. The working data link layer realizes the interconnection of local area networks. 5.8G long distance transmission with 16DBi high gain antenna, up to 5KM. The transmission speed between 2 long range wifi bridge max is 1200Mbps.

Easy to use

1.Unbox everything

2. Switch one unit to A and one unit to B

3. Connect the POE to each unit using the Ethernet cable and plug the POE in

3. Wait for them to power up, about 2 min

4. For 5.8 gh Use the tiny reset button to click through until you get a channel with a letter. A,B,C… Then on the other unit do the same. Both units need to be on the same channel

5. You should see them sync

6. Place the unit you designated B in step 2 above at the existing WiFi point and the unit designated A at the location you are trying to establish extended WiFi

7. Plug at cable from your router to the POE then to the unit

8. At the far end plug a cable in the unit, then to the POE then another cable from the POE to your new router

9. Enjoy

Wifi Bridge for PTP/PTMP

Application Case1:

I have a property that has several office buildings that are spread out over 20 acres and was told that to get internet to these buildings I would have to get someone (electrician) to bury some cables to link all the buildings together or pay for the cable company (specturm) to make drops on every building. The problem with that is there is a paved road that divides the property and that was going to kill any budget to run cables.

I installed this ULNA long range wireless bridge for wifi in 1 hours start to finish with a helper. I have a 300Mbps connection and at the other end of the bridge I was getting 280Mbps. This was a distance of 800 ft but a clear site of view and about 20 ft off the ground. Now that both sides of the road have internet. Avoid digging and wiring and save me a lot of money


Switch Master-Slave Bridge Switch button to"A" indicates the bridge as the master bridge (transmitter), switch button to"B" indicates the bridge as the slave bridge (receiver), a pair of bridges is already preset with A and B, no need to set them again. Note that in the point-to-multipoint application, one of the bridges is used as A and the other bridges are used as B. Then set them both to the same channel number to complete the point-to-multipoint pairing	Only One 1Gbps Port The gigabit wifi bridge has 1 1000Mbps and 100Mbps ports, both of which can accept a 24V PoE power supply, recommended to connect a gigabit port, and the CAT 5e network cable can be used as a power cable to supply power and transmit data. DC power supply is not recommended. Tip: only the PoE port supplies power,the LAN port cannot be powered	Rotate 360° Outdoor wifi bridge kit equipped with a universal wheel, it can rotate 360 to any angl. Easy to adjust antenna orientation for maximum signal strength


Elevator Monitoring Application Using a wireless ethernet bridge to transmit monitoring signals in elevator monitoring can effectively avoid cable damage and obtain stable monitoring images. The wireless bridge is easy to install, supports point-to-point and point-to-multipoint, and can be disassembled and moved to other places for use	Watchdog Function Bridge with watchdog function. When the Wireless Outdoor CPE Kit communication fails, the corresponding unit will automatically detect and restart, restore network communication by itself	Package Included 2 * CPE609 Gigabit Bridge 2 * Gigabit POE Adapter (24V) 2 * Cat 5e Network Cable 2 * Metal Hoop 1 * Mounting Screw Set 1 * User Manual


Pole Mounting 1. Plug the dynamic stick into the bracket. 2. Screw the sealing nut and assembled parts, as well as tighten it. 3. Put the nock washer on the dynamic stick. 4. Assemble the mounting parts to the bridge. 5. Thread the open end of the pole strap through the two tabs on the bracket. 6. Lock and tighten pole strap to secure bracket to the pole	Wall Mounting 1. Plug the dynamic stick into the bracket 2. Screw the sealing nut and assembled parts, as well as tighten it 3. Put the nock washer on the dynamic stick. 4. Assemble the mounting parts to the bridge 5. Determine the mounting location. Mark and drill three 6. Put wall anchors into the holes and insert screw into the wall anchor. 7. Screw and secrue the bracket in the place	Features Gigabit port 16dBi antenna 5.8G channel 27dBm wireless speed Transmission distance up to 5 km Support PC side to modify IP settings Dialing to set the transmitter and receiver WDS networking mode, video network dual compatibility Dynamic MIMO power saving mode (DMPS) and automatic power saving transmission (APSD)