0-210 RPM Power Table Feed CNC Milling Machine X-Axis Milling Table Feed Motor
Welcome to my store：shenzhenwupe
0-210 RPM Power Table Feed CNC Milling Machine X-Axis Milling Table Feed Motor
Please provide the machine type picture before placing the order to judge whether the product meets your needs
The hole diameter of the gear is 16mm;
The size of the center hole to the bottom is about 220mm
The hole diameter of the gear is 16mm;
The size of the center hole to the bottom is about 220mm
Installation Instructions
1. Set the fix stand on work table, set table bearing bushing on the axis screw, then set the power table feed on the fix stand, take out the gear housing.
2. Use one hand to hold the center transmission shaft. Set the bevel gear on axis screw with the other hand. Then check if the backlash between gears is between 0.1-0.2mm.
3. Add shims (1.0t, 0.25t, 0.1t) if the backlash is too large. Repeat step 2-3 until reaching satisfying backlash.
4. Tighten the handle to start setting socket parallel key and bevel gear. Rotate the handle slightly to feel if any interfere occurs in between. If do, please repeat step 3-4 to add more shims. If not, go to next step.
5. Take out the handle, add proper shim (Φ43xΦ33), adjust the backlash between dial & bevel gear and lock with fix ring.
6. Set the handle and tighten, slightly rotate the handle. Normally it should be smooth without any interfere.
7. Finally, set the gear housing and limit switch.
Function：
Power supply switch and reset switch
1. The right side of power switch is “ON”. The left side is OFF. Red light will show when machine is on.
2. The red round button on right side is reset switch. Reset button will jump up to cut off the power if the machine overloads. The operator must reduce cutting load, then press reset switch to continue operating.
Feed knob and rapid button
1. Rotate feed knob after power is on. Turn left for left side feeding and vice versa.
2. The button in the middle is “rapid button”. Tool will travel rapidly to left side if you keep pressing the button. Release to make power table feed will back to normal speed.
Speed adjust knob
Speed can be adjust according to operator’s requirement, ranging from 0-9.
Jog switch
Normally, jog switch should be at “FEED” position. For jog movement, just switch to "0" position. Kept holding the switch until it travels to requires position.
NOTE: To stop jog operating, you must first turn “FEED KNOB” TO “0”(OFF) position. Then move “JOG SWITCH” to “FEED” position.
*Be sure to follow the procedure for jog operation to avoid any damage caused by wrong movement.*
Maintenance
Gear cover must be open every 6 month to check whether lubrication for spiral gear is sufficient. Graphite type lubrication is suggested rather than silicon type.
Carbon brush cap should be open every 6 month to check if the brush has wore out. Brush should be replace immediately if its length is under 5mm (front and back brush should be replaced together).
*Add an auto power table feed to your milling machine! A simple and inexpensive way to increase productivity!*
1. Set the fix stand on work table, set table bearing bushing on the axis screw, then set the power table feed on the fix stand, take out the gear housing.
2. Use one hand to hold the center transmission shaft. Set the bevel gear on axis screw with the other hand. Then check if the backlash between gears is between 0.1-0.2mm.
3. Add shims (1.0t, 0.25t, 0.1t) if the backlash is too large. Repeat step 2-3 until reaching satisfying backlash.
4. Tighten the handle to start setting socket parallel key and bevel gear. Rotate the handle slightly to feel if any interfere occurs in between. If do, please repeat step 3-4 to add more shims. If not, go to next step.
5. Take out the handle, add proper shim (Φ43xΦ33), adjust the backlash between dial & bevel gear and lock with fix ring.
6. Set the handle and tighten, slightly rotate the handle. Normally it should be smooth without any interfere.
7. Finally, set the gear housing and limit switch.
Function：
Power supply switch and reset switch
1. The right side of power switch is “ON”. The left side is OFF. Red light will show when machine is on.
2. The red round button on right side is reset switch. Reset button will jump up to cut off the power if the machine overloads. The operator must reduce cutting load, then press reset switch to continue operating.
Feed knob and rapid button
1. Rotate feed knob after power is on. Turn left for left side feeding and vice versa.
2. The button in the middle is “rapid button”. Tool will travel rapidly to left side if you keep pressing the button. Release to make power table feed will back to normal speed.
Speed adjust knob
Speed can be adjust according to operator’s requirement, ranging from 0-9.
Jog switch
Normally, jog switch should be at “FEED” position. For jog movement, just switch to "0" position. Kept holding the switch until it travels to requires position.
NOTE: To stop jog operating, you must first turn “FEED KNOB” TO “0”(OFF) position. Then move “JOG SWITCH” to “FEED” position.
*Be sure to follow the procedure for jog operation to avoid any damage caused by wrong movement.*
Maintenance
Gear cover must be open every 6 month to check whether lubrication for spiral gear is sufficient. Graphite type lubrication is suggested rather than silicon type.
Carbon brush cap should be open every 6 month to check if the brush has wore out. Brush should be replace immediately if its length is under 5mm (front and back brush should be replaced together).
*Add an auto power table feed to your milling machine! A simple and inexpensive way to increase productivity!*
Highlight：
Noiseless direction changes
Effortless operation
Longer lifespan
Better surface smoothness
Small volume and easy installation
Excellent speed control in the entire range
Jog function operates at any feed speed
Power table feed won't vibrate or strain in low speed
Direction control knob for easy and rapid operation
Safety Highlight to protect transmission gear and electronic
components
Details：
Type: X
Voltage: 220V, 50/60Hz
Current: 2.8A
Max. Torque: 155kg/cm, 135lb/in
R.P.M.: 0-210
Gross Weight: 6kg
Package Dimensions: 29*10*27cm
Package Content：
1 x APF-260 Power Feed
1 x X-Axis Fix Stand with Bushing
1 x Bevel Gear with Fix Ring
1 x Handle Washer
2 x Stop Blocks
2 x Stop Set
2 x Socket Screws (M8*P1.25*35)
2 x Socket Screws (M8*P1.0*25)
6 x Small Shims (Φ26.2*Φ16.2*0.25t)
2 x Small Shims (Φ26.2*Φ16.2*0.1t)
3 x Small Shims (Φ26.2*Φ16.2*1.0t)
4 x Large Shims (Φ43.4*Φ33.4*0.25t)
2 x Spring Pins
1 x Cable Clamp
1 x User Manual
Welcome to our store for shopping.
Our store has a wide range of product categories for you to choose from.
Welcome to click on our store to make a purchase or consult us,
and we will recommend the products you need.??
Our store has a wide range of product categories for you to choose from.
Welcome to click on our store to make a purchase or consult us,
and we will recommend the products you need.??
Welcome to our store for shopping.
Our store has a wide range of product categories for you to choose from.
Welcome to click on our store to make a purchase or consult us,
and we will recommend the products you need.
Our store has a wide range of product categories for you to choose from.
Welcome to click on our store to make a purchase or consult us,
and we will recommend the products you need.
We accept PayPal and bank transfer.
All payments must be made within 7 days after the auction ends. Non-paying bidders will be reported to eBay. Please don't buy an item if you can't/won't pay for it. We accept Credit Cards via PayPal.
4-9 working days to:UK by DHL
5-7 working days to:France ,Germany ,spain ,Italy
6-10 working days to:Other countries
We maintain high standards of excellence and strive for hundred percent customer satisfaction. Feedback is very important to us. We hope that you contact us immediately before you give neutral or negative feedback, so that we can address your concerns. It is impossible to address issues if we do not know about them!
Please keep the original box or packaging within 15days since item received. Returned item must come with original box or packaging.
Your satisfaction is our ultimate goal. We work hard to earn your trust and future business. Our certified technicians have tested each item before shipping. The unit comes with 1 year limited warranty on all manufacturing defects.
a) If you receive a defective item, you may return it or ask for a discount. Please contact us within 14 days after you receive the package.
b) What you returned must be intact and in its original packaging as re? u. Customer is responsible for shipping costs of the returned item.
c) We will cover the cost of shipping back t with the shipping rate indicated in the registration page. We will send you a new unit or refund the full payment you paid.
Thank you.
- Business Hour: Monday To Friday: 8:30 AM to 5:00 PM (Beijing China time)
- Due to time zones, our reply to your questions may not be immediately. But within above working time, we will reply your email within 24 hours. If it's non-workdays, please kindly be patient and wait till Monday.
- Please contact us with ebay message.
- Please feel free to contact us if you have any questions.
