CM4 connector: applicable to all versions of Compute Module 4 Power supply/burning interface: 5V/2.5A power supply, which can also be used as eMMC burning interface DISP interface: MIPI DSI display interface FAN interface: connected with cooling fan, only supporting 5V fan CAM interface: two-way MIPI CSI camera interface HDMI-Compatible interface: HDMI-Compatible interface, supporting 4K 30fps output USB 2.0 interface: 2-way USB 2.0 interface, which supports the insertion of various USB devices Gigabit network port: RJ45 gigabit network port, supporting 10/100/1000M network access M.2 indicator light: indicates the working state of the interface ACT indicator: indicates the working status of strawberry pie Indicates the working status of strawberry pi: indicates the power status of strawberry pie BOOT: ON: cm4 USB type c boot OFF: eMMC or SD card boot 40PIN GPIO interface: it is convenient to connect various HAT modules TF card interface: used to access TFcard with system, only for Lite version HDMI1 cable interface: HDMI1 interface, supporting 4K 30fps output USB 2.0 cable interface: USB 2.0 cable interface, which is connected through the adapter board FE1.1S: USB HUB chip, USB interface 1 expanded by 4 M.2 interface: it is suitable for NVIE solid state disk or communication module supporting PCIE M.2 interface Precautions for use 1. Fan fans only support 5V fans. 12V is not supported. Confirm the fan voltage before connecting. This version of fan has no controller and can't adjust speed. 2. DSi display interface is dsi0 interface, but dsi1 display interface is not connected. 3. Type C interface can be used as power supply or USB slave interface to burn image. 4. In order to ensure the normal power supply of CM4, please do not connect other devices when using type C interface to burn images. 5. When CM4 is in normal use, it needs to provide 5V 2A power supply for CM4. Otherwise, problems such as automatic shutdown and frequency reduction may occur. 6. When using the m.2 interface, please use the matching screws. Using screws of other lengths may cause the CM4 core to be damaged by screws. 7. The module does not have any protection. Please do not short circuit the power supply. 8. USB2.0 is closed by default. To open it, you need to add dtoverlay = dwc2, Dr in config.txt_ mode=host 9. HDMI1 uses flat cable output. If you need to use it, you can buy another HDMI-Compatible adapter 10. Yes, USB 3 / 4 and hdmi1 can be connected by adapter board Note: Due to the different monitor and light effect, the actual color of the item might be slightly different from the color showed on the pictures. Thank you! Please allow 1-2cm measuring deviation due to manual measurement.
Description:
CM4-IO-base-a is the basic io board of the 4th generation of raspberry pi compute module, which can be used with raspberry pi Compute Module 4 and is powered by 5V/ 2.5A USB Type C interface
Feature:
Portable, durable and compact.
This kit includes a .22 cal brass brush, a .22 cal chamber brush, a plastic oil bottle, 2pcs patch holder, 4pcs rifle rods, and a double end nylon cleaning brush.
You will also receive a nice canvas pouch to keep everything in. This is a very handy kit.
Specification:
CM4 connector: applicable to all versions of Compute Module 4
Power supply/burning interface: 5V/2.5A power supply, which can also be used as eMMC burning interface
DISP interface: MIPI DSI display interface
FAN interface: connected with cooling fan, only supporting 5V fan
CAM interface: two-way MIPI CSI camera interface
HDMI-Compatible interface: HDMI-Compatible interface, supporting 4K 30fps output
USB 2.0 interface: 2-way USB 2.0 interface, which supports the insertion of various USB devices
Gigabit network port: RJ45 gigabit network port, supporting 10/100/1000M network access
M.2 indicator light: indicates the working state of the interface
ACT indicator: indicates the working status of strawberry pie
Indicates the working status of strawberry pi: indicates the power status of strawberry pie
BOOT:
ON: cm4 USB type c boot
OFF: eMMC or SD card boot
40PIN GPIO interface: it is convenient to connect various HAT modules
TF card interface: used to access TFcard with system, only for Lite version
HDMI1 cable interface: HDMI1 interface, supporting 4K 30fps output
USB 2.0 cable interface: USB 2.0 cable interface, which is connected through the adapter board
FE1.1S: USB HUB chip, USB interface 1 expanded by 4
M.2 interface: it is suitable for NVIE solid state disk or communication module supporting PCIE M.2 interface
Precautions for use
1. Fan fans only support 5V fans. 12V is not supported. Confirm the fan voltage before connecting. This version of fan has no controller and can't adjust speed.
2. DSi display interface is dsi0 interface, but dsi1 display interface is not connected.
3. Type C interface can be used as power supply or USB slave interface to burn image.
4. In order to ensure the normal power supply of CM4, please do not connect other devices when using type C interface to burn images.
5. When CM4 is in normal use, it needs to provide 5V 2A power supply for CM4. Otherwise, problems such as automatic shutdown and frequency reduction may occur.
6. When using the m.2 interface, please use the matching screws. Using screws of other lengths may cause the CM4 core to be damaged by screws.
7. The module does not have any protection. Please do not short circuit the power supply.
8. USB2.0 is closed by default. To open it, you need to add dtoverlay = dwc2, Dr in config.txt_ mode=host
9. HDMI1 uses flat cable output. If you need to use it, you can buy another HDMI-Compatible adapter
10. Yes, USB 3 / 4 and hdmi1 can be connected by adapter board
Note:
Due to the different monitor and light effect, the actual color of the item might be slightly different from the color showed on the pictures. Thank you!
Please allow 1-2cm measuring deviation due to manual measurement.
