Features:
On Function: When the is on, the motor will not be started immediately no matter the is in any position to injury.
Throttle Stroke Calibration Function: Adapt to the difference of throttle stroke of different , and improve the linearity of throttle response, with smooth, delicate control feel and first-class regulation linearity.
Strong -Interference Capability: The input terminal adopts the ultra-low impedance large-capacity electrolytic capacitor, which greatly improves the -interference ability.
Reduction Function: The output MOSFET tube is equipped with an independent heat sink to reduce the rise of the device and improve the system's high current working capacity.
Independent Voltage-Stabilizing Chip: The -chip microcomputer adopts an independent voltage-stabilizing chip to interference caused by BEC load change and improve the working stability of the -chip microcomputer.
Specifications:
Item Name: 40A Brushless
Material: Silicone Wire, Electronic
Color: Black
Current: 40A
Type: T
Output Capacity: Continuous Current 40A, Short- Current 55A (Not Less Than 10 Seconds)
Input: 2-4 (Not Included)
BEC Output: 5V@3A (Linear Regulator Mode - Linear Mode)
Maximum : 210,000 rpm for A 2- Motor, 7000 rpm for A 6- Motor, 35,000 rpm for A 12- Motor
Size: (Approx) 68*25*8mm
Weight: 32g
Package Information:
Package Size: 128*90*10mm
Package Weight: 33g
Setting Method:
1. Turn on the and push the throttle to the highest ( series transmitters need to use the throttle channel to REV).
2. Connect the receiver and motor.
3. Turn on the . If the is normal, the following sounds are available: (If is a long B sound and then without sound again, please check the throttle channel reverse setting.)
B B: indicates LIPO automatic conservation
BB BB: Indicates NIMH / automatic conservation
BBB BBB: Indicates brake selection
(When there is no operation, all sounds will continue to loop until there is an operation request.)
During the sound loop, when you hear the settings sound you want, pull the throttle to the lowest position quickly at the first syllable that prompts the sound
(For example, LIPO automatic conservation, hear a B sound, and pull the throttle to the lowest position). At the same , the motor will make a very sound to confirm.
At this point, if there is another setting, quickly push the throttle to the maximum, and you can make the choice.
If the setting you want is complete, wait 2 seconds, the motor again emits the appropriate conservation to determine the sound, and confirm the throttle position, then you can use.
LIPO automatic conservation has only two conservation voltage conservation points, and 9V, which can be used without a fully charged .
NIMH automatic conservation is calculated according to the actual number of . Each is set to 0.8V. In order to accurately determine the voltage, please fill the . If not fully charged, the regulator will estimate the conservation voltage at 70% of the voltage. (This function can also be used with 4LIPO)
Brake:
The factory setting is none. A brake setting operation can be performed during actual use, so that the motor brakes with the back electromotive after the throttle is closed.
If you want to release this brake function, you can set the brake operation again, then the function is canceled.
Factory parameter reset function, because this series of has overheating and misoperation conservation function, if you find your acceleration, or steering, or the throttle curve and other characteristics with the new change, you can do it once the Factory parameter settings to regain maximum performance.
Long beep of B for Power On, indicating that the is in the automatic conservation state of LIPO, and the B for three times, indicating that the NIMH/ is automatically conservation state.
Package List: RM15007-1-2
1 * 40A Brushless
On Function: When the is on, the motor will not be started immediately no matter the is in any position to injury.
Throttle Stroke Calibration Function: Adapt to the difference of throttle stroke of different , and improve the linearity of throttle response, with smooth, delicate control feel and first-class regulation linearity.
Strong -Interference Capability: The input terminal adopts the ultra-low impedance large-capacity electrolytic capacitor, which greatly improves the -interference ability.
Reduction Function: The output MOSFET tube is equipped with an independent heat sink to reduce the rise of the device and improve the system's high current working capacity.
Independent Voltage-Stabilizing Chip: The -chip microcomputer adopts an independent voltage-stabilizing chip to interference caused by BEC load change and improve the working stability of the -chip microcomputer.
Specifications:
Item Name: 40A Brushless
Material: Silicone Wire, Electronic
Color: Black
Current: 40A
Type: T
Output Capacity: Continuous Current 40A, Short- Current 55A (Not Less Than 10 Seconds)
Input: 2-4 (Not Included)
BEC Output: 5V@3A (Linear Regulator Mode - Linear Mode)
Maximum : 210,000 rpm for A 2- Motor, 7000 rpm for A 6- Motor, 35,000 rpm for A 12- Motor
Size: (Approx) 68*25*8mm
Weight: 32g
Package Information:
Package Size: 128*90*10mm
Package Weight: 33g
Setting Method:
1. Turn on the and push the throttle to the highest ( series transmitters need to use the throttle channel to REV).
2. Connect the receiver and motor.
3. Turn on the . If the is normal, the following sounds are available: (If is a long B sound and then without sound again, please check the throttle channel reverse setting.)
B B: indicates LIPO automatic conservation
BB BB: Indicates NIMH / automatic conservation
BBB BBB: Indicates brake selection
(When there is no operation, all sounds will continue to loop until there is an operation request.)
During the sound loop, when you hear the settings sound you want, pull the throttle to the lowest position quickly at the first syllable that prompts the sound
(For example, LIPO automatic conservation, hear a B sound, and pull the throttle to the lowest position). At the same , the motor will make a very sound to confirm.
At this point, if there is another setting, quickly push the throttle to the maximum, and you can make the choice.
If the setting you want is complete, wait 2 seconds, the motor again emits the appropriate conservation to determine the sound, and confirm the throttle position, then you can use.
LIPO automatic conservation has only two conservation voltage conservation points, and 9V, which can be used without a fully charged .
NIMH automatic conservation is calculated according to the actual number of . Each is set to 0.8V. In order to accurately determine the voltage, please fill the . If not fully charged, the regulator will estimate the conservation voltage at 70% of the voltage. (This function can also be used with 4LIPO)
Brake:
The factory setting is none. A brake setting operation can be performed during actual use, so that the motor brakes with the back electromotive after the throttle is closed.
If you want to release this brake function, you can set the brake operation again, then the function is canceled.
Factory parameter reset function, because this series of has overheating and misoperation conservation function, if you find your acceleration, or steering, or the throttle curve and other characteristics with the new change, you can do it once the Factory parameter settings to regain maximum performance.
Long beep of B for Power On, indicating that the is in the automatic conservation state of LIPO, and the B for three times, indicating that the NIMH/ is automatically conservation state.
Package List: RM15007-1-2
1 * 40A Brushless