• INITIAL INSPECTION AND GENERAL CARE
  •  
    1. Carefully inspect the air cleaner, air cleaner duct, and the exhaust manifold for any foreign material. Objects left in these areas can severely damage the turbocharger immediately on engine startup. 
    2. Remove old gaskets and left-over material from the exhaust manifold, the oil supply line and oil drain line flanges. Inspect these surfaces for cracks, flatness, or erosion. 
    3. Inspect the oil supply and drain lines for degradation and cracking.  
    4. Make sure that there are no kinks or any other type of restriction or clogging in either line.
     
  • FINAL INSTALLATION
  • Turbocharger Turbo fits Small Engine 100HP Rhino Motorcycle ATV 13900-62D51

    INITIAL INSPECTION AND GENERAL CARE

     

    1. Carefully inspect the air cleaner, air cleaner duct, and the exhaust manifold for any foreign material. Objects left in these areas can severely damage the turbocharger immediately on engine startup. 
    2. Remove old gaskets and left-over material from the exhaust manifold, the oil supply line and oil drain line flanges. Inspect these surfaces for cracks, flatness, or erosion. 
    3. Inspect the oil supply and drain lines for degradation and cracking.  
    4. Make sure that there are no kinks or any other type of restriction or clogging in either line.

     

    FINAL INSTALLATION

     

    1. Install the turbocharger, taking care to ensure that no dirt or foreign material enters the turbocharger openings. Always, use new gaskets and O-rings (where applicable). Do not connect the oil supply line or the air cleaner duct yet, see later steps. 
    2. Pre-lube the turbocharger by pouring clean engine oil into the oil inlet hole of the turbo.  
    3. With your fingers, spin the compressor wheel several times to coat the turbocharger bearings with oil.  
    4. Pour more oil into the oil inlet hole to top it off. There may be some drainage, but this is of no concern. 
    5. Connect the oil supply line and the air cleaner duct. 
    6. Check for proper crankcase oil level. 
    7. With the fuel shut off to prevent engine start, crank the engine for 10-15 seconds, or until the gauge shows an oil pressure build up. 
    8. Start the engine and let it idle for 5-10 minutes. Do not rev the engine during this time. 
    9. Check the installation for any oil leaks.

     

    The installation tips listed here are general guidelines that apply to all turbos and do not include vehicle-specific details. Please refer to the authorized original equipment service manual for detailed installation instructions. If you do not have the experience, proper tools or manuals, please seek the services of a qualified technician.

     

    6 Ways to Protect Your Turbo Engine

     

    1.     Regular Oil Maintenance

     

    For the best performance from a turbocharger, change the oil at least every 5,000 miles.

     

    2.     Warm Up the Engine

     

    For the first 10 minutes of driving a cold car, go easy on the accelerator pedal to limit the strain on the oil pump and prevent unnecessary wear and tear on the turbo system. Wait at least 10 minutes before going full throttle, or watch the oil gauge for when it’s reached its optimum temperature.

     

    3.     Don’t Overstep the Limits of the Turbo when Cruising

     

    When cruising around town or on the motorway, try not to jab the accelerator. Instead, ease the power on slowly to give the turbo a chance to start spinning freely, and use the accelerator sparingly to maintain your speed. While turbos are rigorously stress-tested, and should last the lifetime of the engine, regular bouts of aggressive driving could take their toll, and cause costly issues.

     

    And remember – not only will gentle cruising spare your turbo, it’ll give you great fuel economy, too.

     

    4.     Use Your Gears to Overtake

     

    Whether you’re driving up a long hill, overtaking on an A road or accelerating into the fast lane on the motorway, downshifting into a lower gear is a safer long-term option than relying purely on the turbocharger. Gears were built for aiding performance up and down the rev range, so using a combination of gear changes and turbo boost will help to limit the wear and tear suffered through the turbo system.

     

    5.     Let the Engine Cool After Driving

     

    Turbos produce a lot of heat while driving, and if you turn off the engine straight away, this residual heat will boil the oil in the turbo system, leading to a build-up of carbon particles that can cause corrosion and premature engine wear.

     

    After driving, get in the habit of leaving the engine running for a couple of minutes at idle, which will cool the turbo enough to switch off the engine without cooking the engine oil.

     

    6.     Don’t Blip the Throttle Before Turning the Engine Off

     

    Whether you’re parking or simply want to hear the whizz of the turbo charger, don’t blip the throttle right before turning the ignition off. Pressing the accelerator causes the rotating turbines in the turbo to spin; when the engine is switched off, the flow of oil lubricating these moving parts will stop, but the turbines won’t stop spinning. This puts strain on the bearings, causing friction and a build-up of heat which can lead to a failure in the turbo system.

     

    You can reduce this risk by following the advice in point five – leaving the engine to cool before switching off the ignition.

     


     

     


    Item Specifics
    Brand gdcarpartsin
    Manufacturer Part Number GD106973CAR
    Type Turbo Charger
    Warranty 1 Year
    Placement on Vehicle Front
    Custom Bundle NO
    Fitment Type Direct Replacement
    Interchange Part Number 13900-62D51.A,VZ21.A
    Cross Part Number 13900-62D51.A,1390062D51.A
    Superseded Part Number 1390062D50.A
    Other part number 13900-62D50.A
    Package Contents As the picture shows
    OE Spec or Performance/Custom Performance/Custom
    Fit 1 for Isuzu 4TNA,YA1, F6AT
    Feature ESCP
    Feature ESCP

    Shipping
    1. Orders processed within 24 hours of payment verification.(if you want cancel orders or change address pls contact us within 6 hours after payment,or we are not responsible for shipping a replacement.)
     
    2. We only ship to confirmed PAYPAL addresses. Your PAYPAL address must match your Shipping address.
     
    3. Fast shipping:All our packages use USPS First Class/UPS/Fedex... Package Service
     
    4. If you have not received your shipment within 15 days from payment , please contact!
    Return
    1. You have 30 days to contact us and 10 days to return it from the date it was received. If this item is in your possession more than 7 days, it is considered used and we will not issue you a refund or replacement. There are NO EXCEPTIONS!
     
    2. All returned items must be in the original packaging and you must provide us with the shipping tracking number, specific reason for the return, and item custom lable.
     
    3. We will refund your full winning bid amount, upon receipt of the item in its original condition and packaging with all components and accessories included, AFTER both Buyer and Seller cancel the transaction from eBay. OR, you may choose to have a replacement.
     
    4. Return shipping is to be paid by the Buyer
    Feedback
    We strive for 100% customer satisfaction! FEEDBACK IS VERY IMPORTANT TO US.
    We request that you contact us immediately BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concerns. 
    Payment
    1.We only accept PayPal.
     
    2.Please do not use the PayPal note field to indicate us to ship to other address. The note there will NOT be read. If you want to change the shipping address, please contact us by eBay messages.
     
    3.(if you want cancel orders or change address pls contact us within 6 hours after payment,or we are not responsible for shipping a replacement.)
     
    4.Payment must be received within 10 days as auction ended or order might be delayed.
    Warranty
    1,We stand behind every product we sell.
    2,All of our brand new items come with a 60-Days money-back guarantee.
    3,We define the item as defective only if it doesn't function as described.
    4,It is the buyer's responsibility to understand the item description before bidding.
    5,We will replace the defective items, provided that they are in stock within the warranty period posted with the listing and the buyer return the  original item and pay for the S&H cost for the replacement.
     6,We  will refund the purchase price if the replacement is not available or buyer  prefers a refund and send the original item back at his/her own cost.
    7,Shipping & handling cost are not refundable.
    8,Man-made damage by  abuse or wrong operation is not covered by this warranty.
    9,No  product liability insurance is assumed.

    Shop Category
    Delivery
    Help & Info
    Payment Policy
    Shipping Policy
    Return Policy
    FAQ
    About Us
    Turbocharger Turbo fits Small Engine 100HP Rhino Motorcycle ATV 13900-62D51

    INITIAL INSPECTION AND GENERAL CARE

     

    1. Carefully inspect the air cleaner, air cleaner duct, and the exhaust manifold for any foreign material. Objects left in these areas can severely damage the turbocharger immediately on engine startup. 
    2. Remove old gaskets and left-over material from the exhaust manifold, the oil supply line and oil drain line flanges. Inspect these surfaces for cracks, flatness, or erosion. 
    3. Inspect the oil supply and drain lines for degradation and cracking.  
    4. Make sure that there are no kinks or any other type of restriction or clogging in either line.

     

    FINAL INSTALLATION

     

    1. Install the turbocharger, taking care to ensure that no dirt or foreign material enters the turbocharger openings. Always, use new gaskets and O-rings (where applicable). Do not connect the oil supply line or the air cleaner duct yet, see later steps. 
    2. Pre-lube the turbocharger by pouring clean engine oil into the oil inlet hole of the turbo.  
    3. With your fingers, spin the compressor wheel several times to coat the turbocharger bearings with oil.  
    4. Pour more oil into the oil inlet hole to top it off. There may be some drainage, but this is of no concern. 
    5. Connect the oil supply line and the air cleaner duct. 
    6. Check for proper crankcase oil level. 
    7. With the fuel shut off to prevent engine start, crank the engine for 10-15 seconds, or until the gauge shows an oil pressure build up. 
    8. Start the engine and let it idle for 5-10 minutes. Do not rev the engine during this time. 
    9. Check the installation for any oil leaks.

     

    The installation tips listed here are general guidelines that apply to all turbos and do not include vehicle-specific details. Please refer to the authorized original equipment service manual for detailed installation instructions. If you do not have the experience, proper tools or manuals, please seek the services of a qualified technician.

     

    6 Ways to Protect Your Turbo Engine

     

    1.     Regular Oil Maintenance

     

    For the best performance from a turbocharger, change the oil at least every 5,000 miles.

     

    2.     Warm Up the Engine

     

    For the first 10 minutes of driving a cold car, go easy on the accelerator pedal to limit the strain on the oil pump and prevent unnecessary wear and tear on the turbo system. Wait at least 10 minutes before going full throttle, or watch the oil gauge for when it’s reached its optimum temperature.

     

    3.     Don’t Overstep the Limits of the Turbo when Cruising

     

    When cruising around town or on the motorway, try not to jab the accelerator. Instead, ease the power on slowly to give the turbo a chance to start spinning freely, and use the accelerator sparingly to maintain your speed. While turbos are rigorously stress-tested, and should last the lifetime of the engine, regular bouts of aggressive driving could take their toll, and cause costly issues.

     

    And remember – not only will gentle cruising spare your turbo, it’ll give you great fuel economy, too.

     

    4.     Use Your Gears to Overtake

     

    Whether you’re driving up a long hill, overtaking on an A road or accelerating into the fast lane on the motorway, downshifting into a lower gear is a safer long-term option than relying purely on the turbocharger. Gears were built for aiding performance up and down the rev range, so using a combination of gear changes and turbo boost will help to limit the wear and tear suffered through the turbo system.

     

    5.     Let the Engine Cool After Driving

     

    Turbos produce a lot of heat while driving, and if you turn off the engine straight away, this residual heat will boil the oil in the turbo system, leading to a build-up of carbon particles that can cause corrosion and premature engine wear.

     

    After driving, get in the habit of leaving the engine running for a couple of minutes at idle, which will cool the turbo enough to switch off the engine without cooking the engine oil.

     

    6.     Don’t Blip the Throttle Before Turning the Engine Off

     

    Whether you’re parking or simply want to hear the whizz of the turbo charger, don’t blip the throttle right before turning the ignition off. Pressing the accelerator causes the rotating turbines in the turbo to spin; when the engine is switched off, the flow of oil lubricating these moving parts will stop, but the turbines won’t stop spinning. This puts strain on the bearings, causing friction and a build-up of heat which can lead to a failure in the turbo system.

     

    You can reduce this risk by following the advice in point five – leaving the engine to cool before switching off the ignition.

     


     

     

    Item Specifics
    Brand :gdcarpartsin
    Manufacturer Part Number :GD106973CAR
    Type :Turbo Charger
    Warranty :1 Year
    Placement on Vehicle :Front
    Custom Bundle :NO
    Fitment Type :Direct Replacement
    Interchange Part Number :13900-62D51.A,VZ21.A
    Cross Part Number :13900-62D51.A,1390062D51.A
    Superseded Part Number :1390062D50.A
    Other part number :13900-62D50.A
    Package Contents :As the picture shows
    OE Spec or Performance/Custom :Performance/Custom
    Fit 1 :for Isuzu 4TNA,YA1, F6AT
    Feature :ESCP
    Feature :ESCP


    1. Orders processed within 24 hours of payment verification.(if you want cancel orders or change address pls contact us within 6 hours after payment,or we are not responsible for shipping a replacement.)
     
    2. We only ship to confirmed PAYPAL addresses. Your PAYPAL address must match your Shipping address.
     
    3. Fast shipping:All our packages use USPS First Class/UPS/Fedex... Package Service
     
    4. If you have not received your shipment within 15 days from payment , please contact!
    1. You have 30 days to contact us and 10 days to return it from the date it was received. If this item is in your possession more than 7 days, it is considered used and we will not issue you a refund or replacement. There are NO EXCEPTIONS!
     
    2. All returned items must be in the original packaging and you must provide us with the shipping tracking number, specific reason for the return, and item custom lable.
     
    3. We will refund your full winning bid amount, upon receipt of the item in its original condition and packaging with all components and accessories included, AFTER both Buyer and Seller cancel the transaction from eBay. OR, you may choose to have a replacement.
     
    4. Return shipping is to be paid by the Buyer
    We strive for 100% customer satisfaction! FEEDBACK IS VERY IMPORTANT TO US.
    We request that you contact us immediately BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concerns. 
    1.We only accept PayPal.
     
    2.Please do not use the PayPal note field to indicate us to ship to other address. The note there will NOT be read. If you want to change the shipping address, please contact us by eBay messages.
     
    3.(if you want cancel orders or change address pls contact us within 6 hours after payment,or we are not responsible for shipping a replacement.)
     
    4.Payment must be received within 10 days as auction ended or order might be delayed.
    1,We stand behind every product we sell.
    2,All of our brand new items come with a 60-Days money-back guarantee.
    3,We define the item as defective only if it doesn't function as described.
    4,It is the buyer's responsibility to understand the item description before bidding.
    5,We will replace the defective items, provided that they are in stock within the warranty period posted with the listing and the buyer return the  original item and pay for the S&H cost for the replacement.
     6,We  will refund the purchase price if the replacement is not available or buyer  prefers a refund and send the original item back at his/her own cost.
    7,Shipping & handling cost are not refundable.
    8,Man-made damage by  abuse or wrong operation is not covered by this warranty.
    9,No  product liability insurance is assumed.

    All rights reserved.