Payment Policy Shipping Policy Return Policy FAQ About Us |
Power Steering Rack and Pinion Assembly for 2006-2010 2011 2012 Dodge Ram 1500
Product Description - High-quality replacement
- Not rebuilt or remanufactured
- 100% tested For reliability and performance
- Undergone strict tests to ensure reliable performance
- Hydraulically Tested to Ensure Internal By-Pass for Both High and Low Pressures
- Top performance For long service life
The role of steering gear A power "steering rack" or "steering gear" is a rack gear and a pinion gear that transmits the steering wheel rotation inside of your car to tire movement outside of your car. Most modern steering racks have either a hydraulic pump for assist or electric motor for assist. The rack is connected to the outer steering mechanisms with tie rod ends. - It converts the rotational motion of the steering wheel into the linear motion needed to turn the wheels.
- It provides a gear reduction, making it easier to turn the wheels.
Part Number 55366-383AD-AE,5154494AA,22-382,Rack 5172 Fit for DODGE RAM 1500 2002 - 2005 4WD
DODGE RAM 1500 2006 - 2010 Standard Cab or Crew Cab; Exc. SRT-10
RAM 1500 2011 - 2012 3.7L ST; 5.7L
DODGE RAM 2500 2006 - 2010 2007-2008: RWD Only
RAM 2500 2011 - 2012 RWD
DODGE RAM 3500 2006 - 2010 2007-2008: RWD Only
RAM 3500 2011 - 2012 All Models If you find the following problems, please check or replace them in time - Steering fluid leak
- Unresponsive steering
- Steering wheel vibration
- Clunking noise when turning
- Tight steering wheel
- Steering wheel not returning
- Death wobble
Replace the Steering Rack - Put the wheels in a straight-ahead position. The steering wheel should be in the center position. Remove the key from the ignition and make sure the steering wheel is locked You do not want the steering wheel to turn while removing the rack. Doing so will make it possible for the spiral cable in the steering wheel to unwind and become useless.
- Crack loose all the wheel lug nuts
- Raise and support the vehicle with approved jack stands.
- Remove both front wheels.
- Remove the Steering Shaft Coupler Outer Seal and unbolt the upper pinch bolt on the Steering Shaft Coupler assembly.
- Detach the outer tie rod ends. You may need to use a special tie rod end puller to get them off. You can rent one at the local rental store. Most times a sharp rap with a BFH on the end of the tie rod mount will shock it loose. Do not hit the tie rod end itself.
- Remove any parts required to gain access to the rack mounting bolts, lines and steering coupling.
- Depending on accessibility, at this point, you can remove the power steering rack mounting bolts, or crack the power steering high pressure and return lines.
- Depending on accessibility, at this point, you can remove the power steering rack mounting bolts, or crack the power steering high pressure and return lines. It may be easier to get a wrench to swing on a power steering line fitting once you've unbolted the rack and moved it a bit. Also, reattaching the lines may be easier before the new rack is bolted in place.
- Place a drain pan under the vehicle and remove the hydraulic power steering pressure hose and power steering return hose from the power steering rack.
- Now comes the fun part, twist and turn and jiggle it out through one of the wheel well openings. Make sure the kids are in the house because certain words will be necessary to coax the rack out and they are not words little ears should hear.
- If the new rack has new tie rod ends, measure the overall length of the old rack and tie rod assembly. Set the overall length of the new assembly to this same dimension by twisting the tie rod ends on their threads. Keep the rack centered and split the overlap difference between the left and right rod ends as you do this, or the steering wheel will be off-center when you're done.
- If you are reusing the old tie rod ends, crack the lock nuts loose. Count how many full turns it takes to remove the tie rod ends. Center the new rack and install tie rod ends the same number of turns on the new rack. Again, check the overall length and split the difference.
- Install the new rack using the same words you used to get it out.
- Reconnect the power steering lines, using new "O" rings, if required. Usually, the high-pressure line uses a slightly larger "O" ring so be careful not to mix them up.
- Reconnect the Steering Shaft Coupler assembly and bolt the rack back into place.
- Reattach the tie rod ends to the steering knuckles. Use new cotter pins for the castellated nuts; never reuse the old cotter pins.
- Put the wheels back on and torque the lug nuts to specifications.
- Remove the return line from the power steering pump and place the end into a bucket.
- Fill the power steering pump and start the engine until clean fluid comes out of the return hose. You may be able to install an inline filter in the return line to protect the new rack. I have known guys who have used fuel filters for this purpose.
- Have the front end aligned to reset the toe-in adjustment to specification or the vehicle will handle poorly and wear out the tire quickly.
Note - In order to ensure the normal operation of the steering gear, relevant parts shall be cleaned as much as possible before installation.
- Our products are highly adaptable, please match your model before purchase.
- Please feel free to contact us if you have any questions about our products.
| Item Specifics |
|---|
| Brand : | quality_autoparts | | Type : | Steering Rack,Steering Gear | | Manufacturer Part Number : | Q17101501LA | | OE/OEM Part Number : | 22-382,Rack 5172,55366-383AD-AE,5154494AA | | Item Weight : | 29.48 lb | | Manufacturer Warranty : | 1 Year | | Feature : | Easy Installation | | Item Length : | 55.9 in | | Country/Region of Manufacture : | Unknown | | Performance Part : | Yes | | Vintage Part : | No | | Universal Fitment : | No | | Fitment Type : | Direct Replacement | | Rack Type : | Hydraulic | | Surface Finish : | Rust Protected | | Itment Note : | Top performance For long service life | | Include : | Steering Rack | | Material : | Steel |
Immediate payment is required during checkout. We will process and ship orders once checkout is completed.
We offer international shipping through eBay global shipping program.We reserve the right to change shipping carrier and shipping method for efficient and on-time deliveries. Our store is not responsible for carrier delays such as weather or natural disasters.
All returns must be approved with a Return Material Authorization Number (RMA #) that must be included with the return
To receive an RMA Please contact Our Customer Service.
All returned products will be inspected. Returns processing may take up to 3 business days from the time your product is received at our return facility locations.
Often, Customers reach out to us to help confirm fitment of parts prior to purchase.
We always recommend cross referencing a part number to ensure fitment as well.You may Contact Us by locating the "Contact Seller" Button within a listing.
We maintain high standards of excellence and strive for hundred percent customer satisfaction. Feedback is very important to us. We hope that you contact us immediately before you give neutral or negative feedback, so that we can address your concerns. It is impossible to address issues if we do not know about them!
|
