|
Product Type: FX3U-24MT
Transistor output type: control stepper motor. hydraulic valve. intermediate relay. DC load (maximum 3A)
Power supply: DC24V
Input: X0-X15, (X0-X5 can do high-speed counting input port 12KHZ) a total of 14 points
Output: Y0-Y3 supports high-speed pulse output 100K, Y4-Y11 pulse output 10K, a total of 10
Y0-Y11 can also be used as a normal output to control stepper motors, hydraulic valves, intermediate relays, etc.
Analog input: AD0-AD2 (voltage 0-10V), AD3-AD5 (current 0-20MA), read analog with RD3A instruction
Analog output: 2 channels (voltage 0-10V), output analog with WR3A command
Memory capacity: 8000 steps.
Download baud rate: 38.4Kbps
Programming mode: original programming, downloading, debugging, monitoring (can be easily debugged during monitoring).
Size: shell length 126mm* width 116mm* height 42mm
No software conversion required, the same download method as regular PLC
This product currently supports command set
Basic instructions: LD, LDI, AND, ANI, OR, ORI, OUT, (OUTT, OUTC), SET, RST, ANB, ORB, MPS, MRD,
MPP, INV, LDP, LDF, ANDP, ANDF, ORP, ORF, RET, OUTM, SETM, RSTM, OUTS, SETS,
RSTS, PLS, PLF, MC, MCR, PI, END.
Stepping instructions: STL: Supports 8 parallel branches, different status numbers can have double coils.
Contact comparison instructions:
LD>=, LD<=, LD>, LD<, LD<>, LD=, AND>=, AND<=, AND>, AND<, AND<>, AND=, OR>=, OR<=, OR>, OR<, OR<>, OR=.
Transfer and compare instructions: MOV, CML, XCH, BCD, BIN, CMP, ZCP, FMOV.SMOV.BMOV.
Four arithmetic instructions: ADD, SUB, MUL, DIV, INC, DEC, WAND, WOR, WXOR, NEG.
Cyclic shift instructions: SFTR, SFTL, SFWR, SFRD.
Data processing instructions: ZRST, DECO, ENCO.
Program flow instructions: CJ, CALL, SRET, IRET, EI, DI, FEND, WDT, FOR, NEXT.
Convenient instructions: IST, ABSD, INCD, ALT, RAMP,
High-speed processing instructions:
REF, REFF, MTR, HSCS, HSCR, SPD, PLSY, PWM, PLSR Peripheral I/O ports: DSW, SEGL, FROM, TO.
Peripheral device SER instructions: RS, PRUN, ASCI, HEX, CCD, VRRD, VRSC, PID.
Positioning instructions: ABS, ZRN, PLSV, DRVI, DRVA.
Clock operation: TCMP, TZCP, TADD, TSUB, TRD, TWR, HOUR.
Intermediate relay M: MO-M3071, the power-down storage range can be set to MO-M1023, the default M500-M1023
Step point S: S0-1023, the power-down save range can be set to S0-S1023, the default S500-S9999
100Ms timer: TO-T199, cumulative power-down save T184-T199
10Ms timer: T200-T249, cumulative power-down save T246-T249
1Ms timer: T250-T383, where T250-255 is cumulative
16-bit counter: CO-C199, save power C100-199
32-bit counter: C200-C219, save power C220-C234
C235-255; C235-240 is a single-phase counter, no multiplier; C241-240 is a single-phase counter, 2 times the frequency;
32-bit high-speed counter: C247-249 is a two-phase counter, no multiplier; C250-252 is a two-phase counter, 2 times the frequency; C253-255 is
Dual phase counter, 4 times frequency
Register D: DO-D7999, the power-down save range can be set to DO-7999,
Indirect addressing pointer V, Z: V0-7, Z0-7
P subroutine jump number : PO-63
I interrupt: X0-5 external interrupt. Timer interrupt (1MS is the unit). The counter is interrupted.
Special M components: M8000 is normally closed during operation, M8002 is powered on pulse, M8011 is 10Ms pulse, M8012 is 100Ms pulse, M8013 is 15 pulse, M8014 is minute pulse.
pulseFX3U-24MT industrial control board controller controls stepper motor hydraulic valve intermediate relay Plc high speed pulse
|